
The kinetics of hydrochloric acid leaching of oxidized magnesite–iron nickel ores from the Gornostaevskoye deposit (Eastern Kazakhstan) were investigated. The ore has high contents of Mg (14.25 wt.%), Fe (10.8 wt.%) and Si (24.32 wt.%), with a Ni content of 0.87 wt.%. The optimal process parameters were determined as follows: S:L = 1:4, temperature = 85–90 °C, leaching duration = 120 min, HCl concentration = 18%, and stirring rate = 400 rpm. The extraction rates of Ni, Mg and Fe were 91.03%, 97.88% and 93.04%, respectively. The pregnant leach solution contained 1.98 g L-1 Ni, 35.31 g L-1 Mg and 25.12 g L-1 Fe. Kinetic modeling indicated that the leaching of Ni, Fe, and Mg followed a mixed-control mechanism, with activation energies of 76.07 kJ mol-1 for Ni, 125.45 kJ mol-1 for Fe, and 119.33 kJ mol-1 for Mg, confirming that the chemical reaction was controlled. Thermodynamic analysis revealed that pimelite, nickel silicate hydrate, and antigorite are the most reactive phases under hydrochloric acid leaching, on the basis of their highly negative ΔG values. The established mineral dissolution sequence, namely, pimelite > Ni − silicate hydrate > nepouite > antigorite > lizardite > talc > wüstite > hematite, reflects the combined influence of structural accessibility and thermodynamic favorability.

In open-pit mining, bulk material transportation largely determines productivity and energy costs. Air-cushion belt conveyors reduce friction and wear compared to traditional systems, yet their comprehensive evaluation under real mining and geometric conditions remains limited. Intelligent modeling and automated monitoring enable real-time assessment of key parameters and justify modernization aimed at improving energy efficiency and reliability of logistics systems. The objective of this study is to develop and validate a methodology for assessing the production and economic performance of air-cushion belt conveyors in open-pit mining operations using intelligent modeling and an automated monitoring system. The proposed approach takes into account complex mining and geometric conditions and is aimed at improving the energy efficiency, reliability, and sustainability of transport systems. The methodology combines real-time data collection, digital modeling using artificial intelligence algorithms, and industrial testing at an operating mining facility. Key performance parameters, such as energy consumption, stability, fault tolerance, and automation, are assessed. A comparative analysis of technical and economic indicators before and after the implementation of intelligent technologies is conducted. The results confirm the feasibility and benefits of upgrading air-cushion conveyor systems in combination with artificial intelligence-based tools. This methodology can be applied to optimize bulk material transportation in quarries and improve the overall efficiency of production logistics in the mining and construction industries.

When actual intensity of transport traffic considerably exceeds the planned values, it leads to accelerated wear of road surface and formation of rutting. This problem is actual on high- speed main streets of Almaty city. Rutting in asphalt concrete pavement, especially in the areas of expansion joints, causes impacts of motor vehicles' wheels on the ends of joints (metal trims). Such loads lead to rapid failure of all expansion joints that are fixed in the roadway. It is obvious that the increase in traffic volume contributes to the increase in damage, but it is worth noting that uniform loading with a certain frequency leads to the same result, whereas impact loads occurring after the appearance and progression of damage have a much more damaging effect. To date, most efforts to reduce potholes and rutting at joints with expansion joints have focused on reducing rutting, especially in the areas adjacent to expansion joints.

Research analysis reveals factors influencing third-phase crud formation and composition during metal extraction, including solution composition, solid suspensions, organic compounds, colloidal compounds (e.g., silicic acid), and extractant purity. Compositional analysis of copper-containing sulfuric acid solutions (1.25 g/dm3 copper) identifies principal sulfate-forming components. Copper extraction was studied using extractants LIX 984N, ACORGA M5774, and M5640 at different ratios of the organic phase to the aqueous O:A (from 1:2 to 1:10). Suppressive impact of 10 vol.% CR60 additive on third-phase crud formation during copper extraction with LIX 984N, ACORGA M5774, and M5640 is analyzed, with ACORGA M5774 being the most effective. Physicochemical analysis characterizes CR60’s active substance as poly(sodium 4-styrenesulfonate) with steel-suppression properties, and its structural formula is determined. Optimal copper extraction conditions establish ACORGA M5640’s 24% efficiency, followed by ACORGA M5774 at 15%. CR60 reduces crud formation, with 5 cm3 of ACORGA CR60 added to sulfuric acid solution reducing interfacial crud formation by 2–3 times. Optimal extraction parameters include 1:2 O:A ratio, 20 ± 5 °C temperature, 5 cm3 CR60 additive, 5 min process duration, and 1-day settling time. ACORGA M5774 (10 vol.% in kerosene) is recommended as an extractant, with 2–3 stages of countercurrent extraction.

Due to the sharp increase in demand and prices for nickel and cobalt, the search for new sources of raw materials has become a pressing issue. This study presents a comprehensive thermodynamic and kinetic analysis of the combined method of oxygen-deficient oxidative roasting and subsequent acid leaching to extract nickel and cobalt from pyrite waste sourced from Kazakhstani enterprises. The thermodynamic analysis showed that, under oxygen deficiency, thermal decomposition of higher sulfides forms non-stoichiometric, soluble lower sulfides of iron, nickel, and cobalt. The kinetic study revealed that the process is complex and multi-stage, and that it proceeds at a high rate in the 610–680 °C range, where kinetic factors control it. Activation energies were calculated for three stages: 105–115 kJ/mol for Stage I (450–479.3 °C), 310–320 kJ/mol for Stage II (661.8 °C), and 390–420 kJ/mol for Stage III (749.7–789 °C). Experimental studies confirmed the effectiveness of roasting at 700 °C for 60 minutes. Subsequent sulfuric acid leaching of the obtained sinders under optimal conditions (sulfuric acid excess coefficient R of 1.5 times the stoichiometric amount, temperature of 100 °C, and a duration of 2 hours) yielded high metal recoveries: 94.5% Fe, 93.4% Ni, and 91% Co. The developed technology, combining thermal activation and leaching, proved effective and is recommended for processing similar raw materials.

This article aims to assess the dynamic loads acting on railway track structures during the operation of open wagons in a degraded technical condition, particularly under increased axle load conditions. The study investigates the interaction characteristics between the open wagon and the superstructure of the railway track, focusing on how wear of components and assemblies in the bogie system influences the magnitude and nature of load transmission. A combined experimental and computational analysis of open wagon dynamics was conducted, considering both loaded and empty operating states, as well as varying levels of technical degradation. The findings allow for the identification of critical parameters that influence operational safety and track degradation. Additionally, the study offers recommendations concerning the permissible range of stability margin coefficients and the operating conditions for worn rolling stock under horizontal and vertical loading scenarios. Copyright

The scientific task of the nozzle scheme uses for formation of an air cushion by using the energy of a jet of air supplied under pressure, simultaneously to form an air cushion, as well as to create the driving force of a load-bearing web, was formulated and the main idea of the work was defined. The optimal option to significantly increase the productivity and length of special types of conveyors is to use the energy of a jet of air supplied under pressure simultaneously as an air cushion and as the driving force of the loadcarrying body, which makes it possible to sharply reduce the coefficient of resistance to movement of the load-carrying body and improve its operating conditions. Supporting the load-carrying body with an air cushion allows to increase the speed of movement to 8 to 9 m/s and more, increase the reliability and safety of conveyor operation, and protect the environment.

Eccentric–cycloidal gear reducers represent a promising type of drive for mining conveyor equipment due to their high shock resistance, multi-tooth load distribution and tolerance to contamination. However, the dynamic behavior of the contact interaction between the eccentric tooth and the cycloidal wheel has not been sufficiently quantified. This limits their large-scale implementation in heavy industrial environments. A detailed analysis of vibration stability, contact force patterns, and geometric conformity of the tooth profile is required to assess operational reliability. Purpose of the study. The aim of this research is to perform a numerical investigation of dynamic contact forces and vibration processes in an eccentric–cycloidal gear reducer used in mining conveyor drives and to evaluate the geometric conformity of the transmission by means of spectral and time-domain analysis. Materials and methods. A multibody dynamic model was developed in MSC Adams. The reducer geometry was imported from Autodesk Inventor, including real bearing parameters, material properties, inertial characteristics, and kinematic constraints. The tooth contact was described using a nonlinear Hertzian model with damping and Coulomb friction. Simulations were performed at an input speed of 750 rpm, gear ratio i = 9 and load torque of 2 kN·m. Vibration acceleration, contact force histories, frequency spectra, and impulse loads during tooth engagement were analyzed. Results. The acceleration of the eccentric shaft reached 350 mm/s2due to local oscillations in bearing units, while vibrations in the gear mesh were effectively damped to 0.004 mm/s2. The contact force exhibited a pronounced impulse of approximately 300 N during tooth engagement. Frequency analysis revealed a single dominant harmonic corresponding to the meshing frequency, without additional resonance peaks, indicating high geometric conformity of the cycloidal profile. The minimal contact area reduces the likelihood of pitting and surface chipping. Discussion. The results demonstrate high vibration resistance of the eccentric–cycloidal transmission and its suitability for mining conveyor applications with variable dynamic loads. The impulse nature of the contact force was quantified and shown to be within acceptable limits. Validation on a laboratory conveyor confirmed the accuracy of the numerical model and uniform motion transfer without phase delays. Conclusions. The investigated gear reducer exhibits low dynamic losses, stable load transfer and high vibration resistance. Numerical simulation confirms its potential for reliable operation in mining conveyor drives and its feasibility for replacing traditional gear systems under harsh industrial conditions. General conclusions. The eccentric–cycloidal reducer demonstrates favorable dynamic behavior, with low contact stresses and absence of detrimental resonant harmonics. The results support its further industrial implementation and optimization. Practical significance and future research. The findings may be used for designing energy-efficient conveyor drives, optimizing cycloidal tooth profiles, estimating fatigue life and developing digital twins of gearbox systems. Future research should focus on wear modeling, shaft misalignment effects, and thermo-mechanical behavior of the gear mesh. © 2025, North Caucasian Institute of Mining and Metallurgy, State Technological University. All rights reserved.
Показано 369–376 из 1222