
When actual intensity of transport traffic considerably exceeds the planned values, it leads to accelerated wear of road surface and formation of rutting. This problem is actual on high- speed main streets of Almaty city. Rutting in asphalt concrete pavement, especially in the areas of expansion joints, causes impacts of motor vehicles' wheels on the ends of joints (metal trims). Such loads lead to rapid failure of all expansion joints that are fixed in the roadway. It is obvious that the increase in traffic volume contributes to the increase in damage, but it is worth noting that uniform loading with a certain frequency leads to the same result, whereas impact loads occurring after the appearance and progression of damage have a much more damaging effect. To date, most efforts to reduce potholes and rutting at joints with expansion joints have focused on reducing rutting, especially in the areas adjacent to expansion joints.

Research analysis reveals factors influencing third-phase crud formation and composition during metal extraction, including solution composition, solid suspensions, organic compounds, colloidal compounds (e.g., silicic acid), and extractant purity. Compositional analysis of copper-containing sulfuric acid solutions (1.25 g/dm3 copper) identifies principal sulfate-forming components. Copper extraction was studied using extractants LIX 984N, ACORGA M5774, and M5640 at different ratios of the organic phase to the aqueous O:A (from 1:2 to 1:10). Suppressive impact of 10 vol.% CR60 additive on third-phase crud formation during copper extraction with LIX 984N, ACORGA M5774, and M5640 is analyzed, with ACORGA M5774 being the most effective. Physicochemical analysis characterizes CR60’s active substance as poly(sodium 4-styrenesulfonate) with steel-suppression properties, and its structural formula is determined. Optimal copper extraction conditions establish ACORGA M5640’s 24% efficiency, followed by ACORGA M5774 at 15%. CR60 reduces crud formation, with 5 cm3 of ACORGA CR60 added to sulfuric acid solution reducing interfacial crud formation by 2–3 times. Optimal extraction parameters include 1:2 O:A ratio, 20 ± 5 °C temperature, 5 cm3 CR60 additive, 5 min process duration, and 1-day settling time. ACORGA M5774 (10 vol.% in kerosene) is recommended as an extractant, with 2–3 stages of countercurrent extraction.

Due to the sharp increase in demand and prices for nickel and cobalt, the search for new sources of raw materials has become a pressing issue. This study presents a comprehensive thermodynamic and kinetic analysis of the combined method of oxygen-deficient oxidative roasting and subsequent acid leaching to extract nickel and cobalt from pyrite waste sourced from Kazakhstani enterprises. The thermodynamic analysis showed that, under oxygen deficiency, thermal decomposition of higher sulfides forms non-stoichiometric, soluble lower sulfides of iron, nickel, and cobalt. The kinetic study revealed that the process is complex and multi-stage, and that it proceeds at a high rate in the 610–680 °C range, where kinetic factors control it. Activation energies were calculated for three stages: 105–115 kJ/mol for Stage I (450–479.3 °C), 310–320 kJ/mol for Stage II (661.8 °C), and 390–420 kJ/mol for Stage III (749.7–789 °C). Experimental studies confirmed the effectiveness of roasting at 700 °C for 60 minutes. Subsequent sulfuric acid leaching of the obtained sinders under optimal conditions (sulfuric acid excess coefficient R of 1.5 times the stoichiometric amount, temperature of 100 °C, and a duration of 2 hours) yielded high metal recoveries: 94.5% Fe, 93.4% Ni, and 91% Co. The developed technology, combining thermal activation and leaching, proved effective and is recommended for processing similar raw materials.

This article aims to assess the dynamic loads acting on railway track structures during the operation of open wagons in a degraded technical condition, particularly under increased axle load conditions. The study investigates the interaction characteristics between the open wagon and the superstructure of the railway track, focusing on how wear of components and assemblies in the bogie system influences the magnitude and nature of load transmission. A combined experimental and computational analysis of open wagon dynamics was conducted, considering both loaded and empty operating states, as well as varying levels of technical degradation. The findings allow for the identification of critical parameters that influence operational safety and track degradation. Additionally, the study offers recommendations concerning the permissible range of stability margin coefficients and the operating conditions for worn rolling stock under horizontal and vertical loading scenarios. Copyright

The scientific task of the nozzle scheme uses for formation of an air cushion by using the energy of a jet of air supplied under pressure, simultaneously to form an air cushion, as well as to create the driving force of a load-bearing web, was formulated and the main idea of the work was defined. The optimal option to significantly increase the productivity and length of special types of conveyors is to use the energy of a jet of air supplied under pressure simultaneously as an air cushion and as the driving force of the loadcarrying body, which makes it possible to sharply reduce the coefficient of resistance to movement of the load-carrying body and improve its operating conditions. Supporting the load-carrying body with an air cushion allows to increase the speed of movement to 8 to 9 m/s and more, increase the reliability and safety of conveyor operation, and protect the environment.

Eccentric–cycloidal gear reducers represent a promising type of drive for mining conveyor equipment due to their high shock resistance, multi-tooth load distribution and tolerance to contamination. However, the dynamic behavior of the contact interaction between the eccentric tooth and the cycloidal wheel has not been sufficiently quantified. This limits their large-scale implementation in heavy industrial environments. A detailed analysis of vibration stability, contact force patterns, and geometric conformity of the tooth profile is required to assess operational reliability. Purpose of the study. The aim of this research is to perform a numerical investigation of dynamic contact forces and vibration processes in an eccentric–cycloidal gear reducer used in mining conveyor drives and to evaluate the geometric conformity of the transmission by means of spectral and time-domain analysis. Materials and methods. A multibody dynamic model was developed in MSC Adams. The reducer geometry was imported from Autodesk Inventor, including real bearing parameters, material properties, inertial characteristics, and kinematic constraints. The tooth contact was described using a nonlinear Hertzian model with damping and Coulomb friction. Simulations were performed at an input speed of 750 rpm, gear ratio i = 9 and load torque of 2 kN·m. Vibration acceleration, contact force histories, frequency spectra, and impulse loads during tooth engagement were analyzed. Results. The acceleration of the eccentric shaft reached 350 mm/s2due to local oscillations in bearing units, while vibrations in the gear mesh were effectively damped to 0.004 mm/s2. The contact force exhibited a pronounced impulse of approximately 300 N during tooth engagement. Frequency analysis revealed a single dominant harmonic corresponding to the meshing frequency, without additional resonance peaks, indicating high geometric conformity of the cycloidal profile. The minimal contact area reduces the likelihood of pitting and surface chipping. Discussion. The results demonstrate high vibration resistance of the eccentric–cycloidal transmission and its suitability for mining conveyor applications with variable dynamic loads. The impulse nature of the contact force was quantified and shown to be within acceptable limits. Validation on a laboratory conveyor confirmed the accuracy of the numerical model and uniform motion transfer without phase delays. Conclusions. The investigated gear reducer exhibits low dynamic losses, stable load transfer and high vibration resistance. Numerical simulation confirms its potential for reliable operation in mining conveyor drives and its feasibility for replacing traditional gear systems under harsh industrial conditions. General conclusions. The eccentric–cycloidal reducer demonstrates favorable dynamic behavior, with low contact stresses and absence of detrimental resonant harmonics. The results support its further industrial implementation and optimization. Practical significance and future research. The findings may be used for designing energy-efficient conveyor drives, optimizing cycloidal tooth profiles, estimating fatigue life and developing digital twins of gearbox systems. Future research should focus on wear modeling, shaft misalignment effects, and thermo-mechanical behavior of the gear mesh. © 2025, North Caucasian Institute of Mining and Metallurgy, State Technological University. All rights reserved.

Metallurgy is one of the leaders in terms of the amount of accumulated waste worldwide. Every year the amount of waste placed in dumps, sludge ponds, tailings ponds only grows. However, at present, tailings, slag, dust, etc. of metallurgical enterprises are considered the most promising for secondary use and the extraction of valuable metals from tailings is an important problem in the world. In Kazakhstan, the technology of processing nickel-cobalt-containing tailings is practically undeveloped. Sokolov-Sarybai Mining Production Association Joint-Stock Company (SSGPO JSC) in Kazakhstan, loses more than 7 thousand tons of nickel and 14 thousand tons of cobalt per year. For processing this type of raw material, a combined technology that includes preliminary roasting and leaching processes is acceptable. The aim of the work is a thermodynamic analysis of the roasting process of wet magnetic separation (wms) tailings of the SSGPO JSC, containing such main components as nickel, cobalt and iron sulfides. Thermodynamic analysis of the roasting of wms tailings in the temperature range from 500 to 750°C showed that in the presence of a limited amount of oxygen, the formation of iron sulfides of the following compositions is possible: Fe0.877S, FeS, Fe2S3, Fe7S8. Nickel and cobalt sulfides are converted into Ni3S2, Ni3S4 and CoS0.89, CoS, respectively. In this temperature range, within the homogeneity region, the transformation of cobalt and nickel sulfides also occurs. The calculated values of the Gibbs free energy confirm the possibility of reactions of formation of low-sulfide compounds and the optimal condition for firing is the temperature range of 600-700°C. Depending on the firing conditions, interconversion of iron, nickel and cobalt sulfides occurs. The results of thermodynamic analysis confirm the possibility of extracting iron, nickel and cobalt from wms tailings in the form of soluble low-sulfide compounds with subsequent extraction from the tailings in the form of individual metal powders. Combined technology for processing this type of raw material will be a good example of the use of circular economy principles.

In recent years, there has been an increased demand for nickel-cobalt-containing batteries, which in turn adds a lot of interest in the production of these metals in large volumes. Due to a contraction of the volume of nickel sulfide ores, the majority of producers consider laterite deposits as a potential source of nickel and cobalt. However, processing laterites by traditional pyrometallurgical methods is economically unprofitable. Research has shown that the use of combined and hydrometallurgical methods can be promising. This article is devoted to a review of the results of research and articles on the extraction of nickel and cobalt from laterite ores over the past 20 years. Current technological schemes for the production of nickel and cobalt using combined manufacturing processes are presented, as well as the results of scientific research on increasing the recovery degree of nickel and cobalt from low-grade refractory laterite ores using preliminary activating roasting, various leaching reagents, oxidizing agents, bacteria, etc. Growing interest in nickel production has also been observed in Kazakhstan and research work on the extraction of target metals from local laterite ores is being intensively carried out. According to the investors’ forecast, the first mining in the republic and full commissioning of nickel production are expected in 2025.

In recent years, there has been an increased demand for nickel-cobalt-containing batteries, which in turn adds a lot of interest in the production of these metals in large volumes. Due to a contraction of the volume of nickel sulfide ores, the majority of producers consider laterite deposits as a potential source of nickel and cobalt. However, processing laterites by traditional pyrometallurgical methods is economically unprofitable. Research has shown that the use of combined and hydrometallurgical methods can be promising. This article is devoted to a review of the results of research and articles on the extraction of nickel and cobalt from laterite ores over the past 20 years. Current technological schemes for the production of nickel and cobalt using combined manufacturing processes are presented, as well as the results of scientific research on increasing the recovery degree of nickel and cobalt from low-grade refractory laterite ores using preliminary activating roasting, various leaching reagents, oxidizing agents, bacteria, etc. Growing interest in nickel production has also been observed in Kazakhstan and research work on the extraction of target met als from local laterite ores is being intensively carried out. According to the investors’ forecast, the first mining in the republic and full commissioning of nickel production are expected in 2025.
Introduction. The development of the mining industry requires increasing the durability and safe tool performance life. For bits of mining drilling machines, this problem is often solved by improving the material of the teeth of these bits. The paper presents the results of a study on the development of a technology for the manufacture of hard-alloy drill bits with increased wear resistance and testing of prototypes when drilling hard rocks. Changes in technology have led to changes in the shape of the tooth. Also, purer tungsten powder was used as the initial component. Research methods. The paper studies carbide teeth of bits manufactured at JSC Almalyk Mining and Metallurgical Combine using standard and modified technology. Its structure and chemical composition were studied. Results and discussion. New methods for performing technological operations for the manufacture of carbide teeth (pins) and steel pin bits are developed and mastered. Tungstencobalt teeth were manufactured using VK10KS (90 %W; 10 % Co) hard alloy, produced using tungsten carbide powder synthesized by carbidization of purified tungsten powder. The shape of the tooth surface was changed from ballistic to semi-ballistic. Metallic cobalt powder was used as a binder. Pin bits of the KNSh40×25 type are made of 0.35 C-Cr-Mn-Si steel. Tests of experimental bits were carried out at several mines, as a result of which its suitability for drilling rocks with a hardness of f` = 14–18 was established. The results of industrial operation showed that the durability of the teeth of bits manufactured by JSC Almalyk Mining and Metallurgical Combine is not significantly inferior to bits from European manufacturers. At the same time, the cost of such bits is several times lower.