In this study, 2-acrylamido-2-methyl-1-propane sulfonic acid (AMPS) and allylamine (AA) were copolymerized in an aqueous solution via free radical polymerization using ammonium persulfate as the initiator. The chemical structure and compositions of the copolymers were confirmed by elemental analysis, Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). Monomer reactivity ratios were determined by Fineman-Ross (rAMPS = 0.91 ± 0,01 and rAA = 0.40 ± 0.02), Kelen-Tudos (rAMPS = 1.10 ± 0.02 and rAA = 0.45 ± 0.01) and inverted Fineman-Ross (rAMPS = 0.85 ± 0.01 and rAA = 0.31 ± 0.03) methods. AMPS was found to be more reactive than AA and copolymers had a random composition. The flocculation performance of the copolymer was evaluated in Fe(OH)3 hydrosol. When the concentration of the copolymer in the hydrosol was more than 15 mg/L, the concentration of Fe3+ ions decreased up to 15 times due to flocculation of hydrosol particles. Effect of the concentration of AMPS-AA copolymer on the electropotential (zeta) and particle size of the hydrosol Fe(OH)3 were also studied systematically. It was determined that the zeta potential of the particles decreased from + 58 to + 20 mV and the average particle size of the hydrosol increased approximately 30 times when copolymer concentration in the hydrosol reached to 20 mg/L. © 2021, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.
The copolymer of N,N-diallyl-N,N-dimethylammonium chloride and N-[3-(Dimethylamino)propyl]methacrylamide (DADMAC–DMAPMA) was synthesized by radical polymerization reaction in an aqueous solution in the presence of the initiator ammonium persulfate (NH4)2S2O8. The molar compositions of the synthesized copolymers were determined using FTIR and 1H NMR-spectroscopy, elemental analysis, and conductometric titration. It was found that in the radical copolymerization reaction, the DMAPMA monomer was more active than the DADMAC monomer; for this reason, the resulting copolymers were always enriched in the DMAPMA monomers. The study of the influence of the DADMAC–DMAPMA copolymer on structure-formation in the bentonite suspension showed that this copolymer significantly increased the static shear stress (SSS) of the system. In this case, the structure-forming properties of the copolymer depended on the pH of the medium. The lower the pH level, the better the structure-formation was in the suspension in the presence of the copolymer. The study of antibacterial activity showed that the DADMAC–DMAPMA copolymer had a biocidal effect against sulfate-reducing bacteria (CRB) at a concentration of not less than 0.05 wt.% and can be used to inhibit the growth of this bacteria. © 2023 by the authors.
In this work, a copolymer of N,N-dimethylacrylamide (DMAA) and [(3-methacryloyl-amino)propyl]trimethylammonium chloride (TMAPMACh) with different molar compositions was synthesized by the free radical copolymerization in an aqueous medium in the presence of ammonium persulfate (NH4)2S2O8) as an initiator. The functional and molar composition of the synthesized copolymers was determined by conductometric titration, Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopy. Reactivity coefficients of the monomers were determined using Mayo-Lewis (rTMAPMACh = 1.25 ± 0.02 and rDMAA = 2.00 ± 0.02) and Fineman-Ross (rTMAPMACh = 1.16 ± 0.02 and rDMAA = 2.25 ± 0.02) methods. The influence of the concentration of monomers [M] and initiator [I] on the rate of copolymerization reaction (RC) at 333 K and equimolar ratios of monomers in the initial mixture was investigated. The kinetic equation of the copolymerization reaction of DMAA with TMAPMACh was derived: RС = k×[M]2.70×[I]1.24. The average rate constant of the copolymerization reaction at this temperature was equal to k = 9.72 L2.94 ×mol-2.94×s-1. It was also found that the copolymers DMAA-TMAPMACh have a biocidal effect against thionic bacteria Thiobacillus ferrooxidans (TB) at a minimum concentration of 1.0 wt. %. Although they do not exhibit bactericidal effects against sulfate-reducing bacteria (SRB) bacteria, they do delay their growth at a concentration of 0.2/1.0 wt. %. © Engineered Science Publisher LLC 2024.
In this work, a copolymer of [(3-methacryloylamino)propyl]trimethylammonium chloride (TMAPMACh) and itaconic acid (IA) with different molar composition was synthesized by the method of free radical copolymerization in an aqueous medium in the presence of an initiator (ammonium persulfate, (NH4)2S2O8). The functional and molar composition of the synthesized copolymers was determined by the methods of elemental analysis, conductometric titration, Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). Coefficients of monomer reactivity were determined using Mayo-Lewis (rTMAPMACh=0.50±0.02 and rIA=1.50±0.02) and Fineman-Ross (rTMAPMACh=0.44±0.02 and rIA=1.51±0.02) methods. It is established that in the radical copolymerization reaction, monomer IA is more reactive than monomer TMAPMACh, and copolymers with a more statistically uniform distribution of monomer units along the macromolecule chain are formed. The influence of the concentration of monomers [M] and initiator [I] on the rate of copolymerization reaction (Rc) at 343 K and equimolar ratios of monomers in the initial mixture was investigated. The kinetic equation of copolymerization reaction in a mixture of TMAPMACh with IA was obtained: RС =k×[M]1.66×[I]0.35. The average rate constant of the copolymerization reaction for this temperature was k=0,049×L0.92 ×mol-0.92×s-1. The results of the copolymerization reaction kinetics make it possible to regulate the process of copolymer formation and thereby obtain a polymer surfactant with the required physicochemical properties. The TMAPMACh-IA copolymer has a biocidal effect against sulfate-reducing bacteria (SRB), and therefore can be used to suppress the growth of this bacteria. © Engineered Science Publisher LLC 2024.

People with walking disorders caused by accidents or stroke can undergo treatment to restore their mobility. Traditional therapy is time-consuming and time-consuming. Therefore, a new trend was born - to facilitate rehabilitation and reduce the patient's time. Rehabilitation robotics is an area that is constantly evolving, and new mechanisms have recently been developed to help people regain their mobility. This paper presents a 3-RPS parallel manipulator for the restoration of the ankle joint with three degrees of freedom. Parallel manipulator 3-RPS with three degrees of freedom, which was introduced by K. Hunt in 1983 as one of the sedentary parallel manipulators. Since then, 3-RPS has attracted a lot of attention from robotics and biomedical engineering engineers. Copyright © 2023 Nursultan Zhetenbayev, et al.

Industrial robots cover most of the field of technology and are most successfully applied in machining, in motion modelling, in capturing and moving objects of research. In recent times, the complexity and variety of industrial robots and robotic manipulators have increased significantly. These are purposefully designed to attain a much greater level of independence than what is seen in conventional mechanical manipulators. In this article the classification of different configurations of manipulators and analysis of manipulators with artificial vision on the existing research of scientists is conducted. Also, the article analyzes the development of a manipulator with six degrees of freedom and the use of analytical methods to analyze the geometric structure of 3D data for optimal object recognition. © 2024 American Institute of Physics Inc.. All rights reserved.

Stenosis, characterized by the narrowing of blood vessels due to plaque accumulation, significantly impacts blood flow dynamics and poses risks such as blood clot formation. This study investigates blood flow in a mildly stenosed, catheterized artery, modeled as a two-dimensional axisymmetric tube, utilizing the incompressible viscous Navier–Stokes equations. Blood is treated as a non-Newtonian fluid, with the Carreau model applied to capture its rheological properties. The Semi-Implicit Method for Pressure-Linked Equations method, renowned for its computational efficiency in solving incompressible flow equations, is employed alongside the finite volume method to ensure local conservation of mass, momentum, and energy. Validation through a planar Poiseuille flow simulation and experimental data demonstrated concordance between numerical and analytical/experimental results, affirming the accuracy of the velocity profile for laminar flow. Subsequent real-case analysis involved a bifurcating artery in a 60-year-old male with atherosclerosis. Findings revealed that the presence of plaques increased wall shear stress (up to 5.5 Pa) at the throat of the stenosis, accompanied by low wall shear stress regions (approximately 0.5 Pa) downstream. A sharp pressure gradient was observed, with upstream pressure reaching 20 Pa and dropping significantly downstream of the stenosis. Velocity distribution showed peak values of approximately 0.2 m/s in the stenosed artery compared to 0.12 m/s in the non-stenosed case. Flow disturbances, including vortex formation and recirculation zones, were identified downstream of the stenosis, contributing to potential vessel wall corrosion and plaque instability. The study concludes that plaques induce significant hemodynamic changes, including low flow velocity regions, altered wall shear stress, and pressure gradients, which can precipitate plaque rupture and atherosclerosis.
This paper investigates the effect of partial replacement of cement with fly ash and ground volcanic tuff on the physical and mechanical properties of concrete. The main focus is on the changes in average density and compressive strength at different contents of replacement materials (from 10% to 35%). The investigated concrete composition (27PPPF) without admixtures has an average density of 1925.5 kg/m³ and compressive strength of 40.1 MPa. The results show that when fly ash is added, the concrete strength first increases, reaching a maximum value of 41.6 MPa at 10% cement replacement and then decreases to 29.1 MPa at 35% replacement. A similar trend is observed when tuff is introduced, but the peak strength (40.7 MPa) is also reached at 10% replacement, after which the strength gradually decreases to 27.9 MPa at 35%. The average density of the specimens changes insignificantly, being in the range of 1910.4-1928.5 kg/m³, which indicates that the dense structure of the concrete is maintained. Thus, the optimum content of fly ash and tuff in the concrete composition is 10-15%, as these values provide the best mechanical characteristics. Higher dosages of substitutes result in lower strength due to thinning of cement stone and lack of binding properties. This study confirms the possibility of using fly ash and volcanic tuff as effective pozzolanic additives to improve the environmental friendliness and sustainability of concrete. © 2026, Institute of Metallurgy and Ore Beneficiation JSC. All rights reserved.
Показано 249–256 из 1222