
The issues of construction are considered and an example of the implementation of the transformation function of an intelligent sensor for the surface temperature of an electrical contact is given. It is shown that the intellectualization of the process of measuring hard-to-reach contact surfaces of the temperature of high-voltage and high-current electrical contact connections is not valid. The term "intelligent" in relation to devices that acquire new qualities due to the processing of the received information in them, is often used in a narrow sense in the presence of the following features: compensation of measurement errors, transmission and processing of the digitized signal of the primary converter. In a broad sense, an "intelligent" sensor, in addition to the above, has the ability to adapt to the signal source and the environment; it is an electronic device that combines sensing elements, signal conversion circuits and microprocessor technology (integration). Application of the principle of the measurement algorithm simplifies the improvement of measurement accuracy by transferring hardware solutions to microcontroller programs. With this deviation of the results, the conversion function of the correction factors is eliminated. This article discusses the construction issues and provides an example of the implementation of the transformation of an intelligent temperature sensor of the contact surface of an electrical contact.

With the increasing integration of the solar energy system into interconnected lines, solar energy systems have a great impact on power quality issues. This study describes the design of single phase inverters that are used to utilize a solar power system and analyze their performance. This article focuses on modeling a single phase inverter. An inverter is a circuit that converts DC power supplies to AC power supplies. The model is implemented using the MATLAB Simulink software with the SimPower System Block Set based on computer simulation. FFT analysis is used to find harmonic distortion using MATLAB Simulink software

Based on the reference thermodynamic data, a four-component Fe-Zr-Al-Si system is constructed and its mathematical model of the phase structure is created. As a result, it turned out that it consists of 12 elementary tetrahedra. For each of the tetrahedra, analytical equations are defined, with the help of which it is possible to determine the location in the factor space of the general system of compositions of various metal melts with the calculation of their standard phase compositions. The breakdown of the overall system is carried out taking into account congruent connections. The sum of the relative volumes of elementary tetrahedra is equal to one (1.00000), which confirms the correctness of the tetrahedron. Quasi-volumes in the Fe-Zr-Al-Si system are established, which simulate the compositions of the metal products formed during the smelting of various ferrosilicocyrconium alloys during the reduction process . As a result, it was found that the alloy with a 25% Zr content is modeled by the Si-Fe2Al5-FeSi2 - Zr6Si5 tetrahedron, and the alloy compositions with 35 and 50% Zr are decomposed in the Si-Fe2Al5-FeSi2 - Zr6Si5 and Zr5Si3-Fe-Fe2Al5-FeSi tetrahedra, respectively.

The electrohydraulic method of natural diatomite enrichment based on separation of the clay component under the influence of plasma energy arising at a short electric discharge is applied for the first time. Special computer technology is developed for the first time, using the portable navigator Montana series 600 by Garmin, Google Earth and Garmin Base Camp programs to make a contour and area of diatomaceous rocks on Zhalpak territory. Comprehensive study of enriched diatomite using spectral, microscopic, X-ray diffractometric, silicate (chemical), elemental and thermal methods of analysis were carried out. Independent methods of analysis show almost identical results for the degree of diatomite enrichment with silicon oxide (SiO2), being in the range of 78÷81.8%. Based on the results of spectral analysis it can be concluded that the electrohydraulic method is very effective in cleaning diatomite from calcium (CaO) and sulfur (SO3) oxides to the level of 0.21% and 0.18% respectively.

The paper provides a literature review on the mechanisms of damping in alloys. The goal of the authors was to obtain the maximum damping with the minimum alloying. Samples of alloys in cast, annealed and quenched form were investigated. According to the research findings, the characteristics of the damping properties of the alloys are provided and the possible reasons for the high values of the damping parameters are explained. An analysis of the nature of non-metallic inclusions shows that very small non-metallic inclusions do not result in high damping. A very high content of medium-sized non-metallic inclusions leads to low sound emission. High alloying with elements such as Mn, Ni, Nb, Al, one percent each, 1.5% Cr, 1.5% V, 0.5% Mo, 0.5% Ti, 0.5% Cu, does not always provide increased damping properties.

In recent years, many researches have been able to redefine the use of the most basic and richest renewable resource – biomass, especially lignocellulose. This article presents the results on the production of lignin from sawdust waste, as well as the production of lignin fibers by electrospinning. A technique has been developed for the extraction of lignin and the production of inexpensive electroformed fibers from lignin with high performance characteristics for energy storage. The obtained samples (lignin and lignin fibers) were examined by physicochemical methods, such as: IR spectroscopy, Raman spectroscopy, Optical microscopy, Electron microscopy (SEM), Elemental analysis.

Improving hydrometallurgical methods for processing copper-containing sulfide natural materials is an urgent task due to the increasing environmental problems, depletion and complexity of the composition of processed raw materials. The kinetic regularities of the process of extracting copper into solution from the solid phase of bornite by alkaline solutions of glycine and hydrogen peroxide are investigated. The kinetics was studied at room temperature and a concentration of 0.1 M hydrogen peroxide. The glycine concentration varied from 0.1 to 1.0 M. In the studied pH range of the medium (8÷11), glycine exists in the form of glycinate anions that react with Cu2+ ions to form a stable copper (II) glycinate, which contributes to the effective extraction of copper from the mineral into the solution. The introduction of an oxidizer – hydrogen peroxide into the system significantly increased the extraction of Cu2+ ions into the solution. The degree of extraction of copper from bornite in the first 10 minutes varied in the range from 29 to 37 %. The results of the conducted studies allow us to consider alkaline solutions of glycine and hydrogen peroxide as a promising solvent reagent for leaching copper from sulfide mineral raw materials.

This paper considers the optoelectronic properties of porous nanostructured silicon obtained by electrochemical etching method. It was noted that the electrolyte concentration affects the depth of porosity, while the anodizing current density affects the density and size of crystallites, as well as the photoluminescence spectra. The results of the Raman measurement showed a low-frequency shift of the wavenumber on the 504 cm-1 line, which changes the frequency difference Δω to 16 cm-1 wavenumber units, while the cross-sectional diameter of the nanocrystallites is distributed from 2.3 nm to 4.3 nm.