The article discusses the forces that arise when a TE-33A diesel locomotive moves through a switch. The analysis of dynamic loads acting on rail threads, crosspieces, and other switch elements is carried out. The purpose of this article is to determine the efforts of the TE-33A diesel locomotive acting on the main elements of the railway track switch. The measurements were carried out in accordance with the requirements using a strain gauge measuring and computing complex consisting of certified and verified measuring instruments from the world's leading manufacturers. As a result of theoretical analysis and experimental studies, the lateral and vertical forces transmitted by the wheels to the inner and outer rails of the transfer curve were determined when the TE-33A locomotive was moving along the R65 mark 1/11 switch. Possible causes of increased wear of the switch elements under the influence of the TE-33A diesel locomotive have been identified. Recommendations are proposed to reduce the negative impact on the switches, including optimizing driving modes. Based on the results obtained, diagrams of vertical and transverse forces were constructed, and indicators of the stress rate at maximum speed along the arrow of the locomotive in question were established.

The development of a country's economy largely depends on the pace and efficiency of construction work, which, in turn, is determined by the extent to which innovative technologies and techniques are used. This work is devoted to justification of the basic parameters and the development of a new working body for a machine for cutting joints in road surfaces. A design with cycloidal motion is proposed, which intensifies the destruction process due to the vibrational impact of the cutters on the material being processed. The use of such a working body provides a vibrational effect, increases the cutting speed, and reduces the energy consumption of the process. As a result of intensifying the interaction between the working body and the material, it was possible to reduce the energy consumption of cutting by 1.13 times, and increase productivity by 1.18 times compared to analogues.

Given the shortage of petroleum bitumen in the Republic of Kazakhstan, the use of local bitumen-containing rocks is becoming increasingly relevant, which requires the development of specialized mechanization tools. In this paper are discussed the special excavator buckets designed for year-round extraction of rocks with a bitumen content of up to 25%. The design features of the bucket that reduce resistance during digging and unloading are described. Calculations of resistance, chip thickness, operation duration, and productivity of the EO-4121 excavator at different temperatures and bitumen contents were performed. It is shown that unloading becomes more difficult when the bitumen content exceeds 18.2%. A comparison of the calculated and experimental data confirmed the high accuracy of the models used

In this study is presented an analytical mathematical model developed to determine the forces arising during the active penetration of machine working bodies into sticky rocks. The methodology is based on the method of element-by-element calculation of resistances, where the contact zone is divided into discrete prisms of material. As a result of the analysis, a final formula for the total penetration force is derived. This formula shows the dependence of the resistance force on the dimensions of the tool (thickness, depth, angle of sharpening) and the physical characteristics of the rock (internal friction, adhesion, stickiness). The model serves as a reliable engineering tool for the design and optimization of working bodies of earthmoving and mining equipment

The influence of the cutting angle on the resistance to the bulldozer blade burial during its movement, taking into account the one-sided stressed state of the soil, was studied in the research results of which are presented in this paper. It is established that the resistance to deepening is significantly reduced when the machine is moving, which allows using smaller cutting angles without increasing the energy consumption. Constructive features and kinematics of the working equipment are considered, including a promising parallelogram scheme, which provides automatic reduction of the cutting angle during deepening. Calculations of the resistance of the blade penetration into the ground, and experimental data confirming the cutting force reduction up to 7%, for each degree of angle reduction, are given. It is determined that the optimum cutting angle is 30-40°. The obtained results can be used to increase the productivity of bulldozers and optimize the design of their working equipment
Metal pollution from metallurgical emissions poses serious environmental and public health risks in Kazakhstan. A replicated pot-culture experiment (n = 4) in a completely randomized design under controlled phytotron conditions evaluated biomass production and metal accumulation in six crop and forage species, alfalfa (Medicago sativa), amaranth (Amaranthus spp.), corn (Zea mays), mustard (Brassica juncea), rapeseed (Brassica napus), and sunflower (Helianthus annuus); three ornamental species, purple coneflower (Echinacea purpurea), marigold (Tagetes spp., ‘Tiger Eyes’), and sweet alyssum (Lobularia maritima); and three native wild plants, greater burdock (Arctium lappa), horse sorrel (Rumex confertus), and mug wort (Artemisia vulgaris). Plants were grown in soils collected from the Qarmet industrial zone in Temirtau, central Kazakhstan. Initial soil analysis revealed substantial mixed-metal contamination, ranked as Mn > Ba > Zn > Sr > Cr > Pb > Cu > Ni > B > Co. Mn reached 1059 mg·kg−1, ~50-fold higher than B (22.7 mg·kg−1). Ba (620 mg·kg−1) exceeded FAO/WHO limits sixfold, Zn (204 mg·kg−1) surpassed the lower threshold, and Pb (41.6 mg·kg−1) approached permissible levels, while Cr, Cu, Ni, Co, and Sr were lower. Biomass production varied markedly among species: corn and sunflower produced the highest shoot biomass (126.8 and 60.9 g·plant−1), whereas horse sorrel had the greatest root biomass (54.4 g·plant−1). Root-to-shoot ratios indicated shoot-oriented growth (>1–8) in most species, except horse sorrel and burdock (<1). Metal accumulation was strongly species-specific. Corn and marigold accumulated Co, Pb, Cr, Mn, Ni, Cu, B, and Ba but showed limited translocation (transfer function, TF < 0.5), whereas sunflower, amaranth, and mug wort exhibited moderate to high translocation (TF > 0.8 to <1) for selected metals. Corn is recommended for high-biomass metal removal, marigold for stabilization, sunflower, horse sorrel, and mug wort for multi-metal extraction, and amaranth and coneflower for targeted Co, Ni, and Cu translocation, supporting sustainable remediation of industrially contaminated soils.

This study evaluates the safety and performance of reinforced concrete culverts manufactured using advanced German (MBK) and Danish (PEDERSHAAB) technology. A 1.0 m diameter culvert with a flat base was subjected to static tests to evaluate crack resistance and strength. The culvert was made of concrete of class B33.5 with a compressive strength of 43.2 MPa, reinforced with steel bars of A400 class. No cracks were observed at the crack resistance test load of 143 kN, but the first crack appeared at a load of 268.8 kN with a width of 0.05 mm, well below the allowable limit of 0.2 mm. The strength tests showed that the culvert withstood a load of 332.1 kN, exceeding the design load of 294.6 kN without reaching the limit state. These results confirm that the culvert complies with safety standards (SP RK 3.03-112-2013 and GOST 8829-94) and is suitable for installation under embankments up to 7.0 m high. Finite element modeling (FEM) in MIDAS FEA NX 2023 confirmed the experimental data. A 1.5 m diameter culvert compared to a 1.0 m diameter culvert has a higher energy intensity after cracking, which is due to a complex of factors.

This study presents a field-based assessment of the operational safety of a reinforced concrete overpass in Astana, Kazakhstan, using combined static and dynamic load testing. The structure is a three-span overpass with 41.0 m reinforced concrete main spans formed by prefabricated UBS 187.14 blocks with variable cross-sections. Static tests were conducted using six ballast-loaded trucks with an average weight of 21.0 t, while dynamic tests were performed under moving vehicle loads at speeds ranging from 3.5 to 70 km/h. The measured maximum static deflection at midspan was 23.5 mm, which is substantially lower than the regulatory limit of 102.5 mm for the 41 m span. Dynamic measurements showed stable structural behavior, with principal frequencies of 3.37–3.39 Hz in the main vibration modes and damping ratios of 3.5%–3.8%, exceeding the minimum reference value of 1.5% for reinforced concrete structures. The recorded vibration periods were outside the code-defined critical ranges, indicating no resonance-related operational concern.
Показано 345–352 из 1222