
Ozonation of water is the most effective method of purifying water and preventing its contamination with various harmful and dangerous components. This method is used in urban water supply. During the purification process, ozone is able to oxidize pollutants of any origin to insoluble compounds that are safe for human health. Ozone is a safe substance for chemical water purification. Ozone water purification is widely used today due to the need for deep purification of water for its reuse. This study examines the results of a comparative analysis of the use of ozone and chlorine reagents in water purification processes. The comparative analysis is presented in the following aspects: the laws of ozone solubility in water, the effectiveness of inactivation of microorganisms, corrosion activity, environmental impact assessment at the stages of the life cycle and life cycle cost assessment. In general, ozone technology is one of the modern methods aimed at effectively purifying water from harmful compounds. The use of ozone for water purification ensures the destruction of bacteria, viruses and other harmful microorganisms, as well as reducing the content of organic and inorganic pollutants. One of the main advantages of using ozone is its high oxidizing ability, which increases the purity of water and facilitates the removal of various pollutants. The work carried out a life cycle assessment, which helps to determine the environmental characteristics of various cleaning agents, including their production, preparation of reagents and the immediate stages of the cleaning process. Based on life cycle assessments, it was possible to predict the potential impact on ecosystems and the depletion of natural resources for various categories of impact, which made it possible to justify the choice of the best technology when comparing alternative technologies. Of all the options considered, sodium hypochlorite is the most effective chlorine-containing reagent. The results of the study, compared with chlorine-containing reagents, revealed the most effective method of water purification based on ozone.

Relevance. The stability of pit walls is a key factor determining the safety and efficiency of open-pit mining operations. Excessive groundwater inflow and the presence of water-saturated zones often lead to slope instability, landslides, and reduced productivity. Therefore, developing effective methods for dewatering pit wall massifs is of great practical significance for ensuring sustainable mining operations. Objective. The objective of this study was to develop and implement a comprehensive system for draining the pit wall massif using newly designed horizontal and slightly inclined boreholes with camouflet cavities to enhance slope stability. Methods. The research methodology involved advanced groundwater interception in formation zones beyond pit boundaries and interception of surface runoff along pit slopes using horizontal, slightly inclined boreholes with camouflet cavities. Experimental investigations were carried out using a polarization optical setup to analyze stress distribution within the rock mass. Field studies included drilling horizontal boreholes in areas of maximum groundwater accumulation, creating camouflet cavities by controlled blasting, and assessing stress redistribution in the dewatered rock mass. The results demonstrated that camouflet cavities formed beyond the rock mass displacement line act as stress concentrators that effectively unload the near-contour zone and enhance slope stability. The introduction of horizontal, slightly inclined boreholes with camouflet cavities ensures efficient drainage of the contour massif, reduces stress concentrations at the slope base, and stabilizes the overall pit wall structure. The proposed set of measures can be widely applied at mining enterprises under similar geological and hydrogeological conditions, contributing to improved safety and productivity in open-pit mining. © 2025, National Academy of Sciences of the Republic of Kazakhstan. All rights reserved.

Currently, the demand for rare earth elements (REE) has increased significantly due to the expansion of volumes and applications in various industries. The annual increase in consumption of specific elements of rare earths is up to 25% per year. To solve the problem of increasing REE production, it is necessary to involve difficult-to-enrich raw materials in processing, which include the weathering mantle of the Kundybay deposit (Kazakhstan). A special feature of this deposit is the increased proportion (54%) of yttrium oxides, medium and heavy lanthanides. As a result of the conducted research, the granulometric and fractional composition of the ore was determined, which made it possible to determine the distribution of REE by the grain-size class of the ore under study. An analysis of the results showed that 29.35% of REE were contained in the grain-size classes more than 0.02 mm, and 70.65% of REE were in fine class –0.02+0.01 mm, –0.01+0.005 mm and less than 0.005 mm. Large classes were characterized by the presence of grains of minerals of low specific gravity with a reduced REE concentration, which determined the possibility of removing depleted fractions by gravity methods. To assess the possibility of using gravity technology for the enrichment of rare earth ore from the weathering mantle of the Kundybay deposit, a fractional analysis of the machine classes of crushed ore with a size of –2.50+0.315 mm and –0.315+0.10 mm was performed. The results of fractional analysis showed that REE were concentrated in minerals of increased density (more than 2850 kg/m3). Based on the results obtained, the possibility of extracting REE from both its slurry and sand fractions has been determined. For the studied ore of the Kundybay deposit, the use of a combined scheme is proposed, including gravitational enrichment of granular classes and subsequent hydro-and pyrometallurgical processing of enriched granular and slurry classes. Based on the conducted experimental and enlarged technological studies, the use of a bowl centrifugal separator in the process of gravitational enrichment is justified, which allows to intensify the extraction of minerals concentrating rare earth elements from relatively small ore classes. The application of the developed scheme using combined gravity enrichment technology with a combination of screw and bowl centrifugal separators ensures an increase in the content of ΣREE in gravity concentrate from 640 to 1054 g/t with the extraction of ΣREE into concentrate and industrial products of more than 70%. An additional economic effect is achieved by removing final tailings from the enrichment scheme and reducing by 30% the yield of products sent for hydrometallurgical processing.

Strength and stiffness assessment of rod mechanisms and robotic manipulators is commonly performed using finite element methods (FEM), while motion-induced inertia is often represented by resultant forces and moments applied at link centers of mass. This simplification is inherently approximate because inertial and gravitational forces are distributed along the link and depend on instantaneous kinematics. The main contribution of this paper is a systematic FEM-ready algorithm that extends a previously planar distributed-inertia concept to a formulation applicable to both planar and spatial rod models. The proposed approach computes distributed inertial and weight load intensities in the local coordinate system of each moving rod from kinematic quantities (link orientation, angular velocity/acceleration, and pole accelerations), transforms them into consistent equivalent nodal forces and moments, and assembles them into the global FEM equilibrium system for strength and stiffness calculations. Unlike flexible multibody dynamics formulations (e.g., floating frame of reference formulation (FFRF)/ANCF) absolute nodal coordinate formulation, which primarily target time-domain dynamic simulation, the proposed method is design-oriented and directly produces configuration-dependent engineering outputs-bending moments, axial forces, and longitudinal/transverse displacements-required for link cross-section sizing and stress assessment. The method is demonstrated on a six-bar planar mechanism to illustrate the influence of distributed inertia on internal force and deformation diagrams at low and high driving speeds.

The relevance of the topic is due to the need to design and construct foundations in conditions of dense urban development and weak soils. The aim of this work is to study the features of pile foundation design, taking into account the stability of the excavation and the effect of phased loading on foundation settlement. The novelty of the research lies in the numerical modeling of phased construction using a wall in the ground, as well as the analysis of changes in the stress-strain state of the foundation, taking into account the stages of pile installation. Calculations performed in the Plaxis 2D software environment showed that when a five-story building is fully loaded, the foundation settlement does not exceed 1 cm, which is within the maximum permissible values according to the standards. The maximum horizontal displacement of the enclosing wall was 0.45 cm, which also indicates its stability at an excavation depth of up to 3 m and the presence of anchors. The results confirm the effectiveness of the combined system—walls in the ground, anchors, and pile foundations—when building on weak soils in confined conditions. The work is of practical value for the engineering and geotechnical justification of construction solutions in densely built-up areas.

The article focuses on the study of the processes intended for copper smelting slag processing, in order to extract such valuable components as copper, zinc, iron and silica. Various options for slag leaching with the use of sulfuric acid as one of the most promising approaches are considered. Preliminary thermodynamic calculations confirmed the high probability of dissolution of metal oxides when interacting with sulfuric acid. High-temperature leaching resulted in higher recovery rates for copper and other valuable metals. The use of sulfuric acid at the concentration of 50 g/dm3 in combination with the optimization of leaching parameters provided the high efficiency of valuable metal extraction—copper up to 76%, zinc up to 94% and iron in the form of oxide up to 92%. Acceleration of pulp filtering was achieved through two-stage re-pulping with hot water. The study results confirm the prospects of hydrometallurgical methods of slag processing. It opens up opportunities for the development of more efficient technologies for processing copper smelting waste, aimed at maximum extraction of useful components at minimal costs.

The rapid advancement of high-technology industries critically depends on the supply of rare earth elements (REEs), which constitute strategic raw materials for knowledgeintensive sectors. This study proposes an integrated methodological framework for the development of the Kundybay REE deposit, combining geomechanical substantiation of open-pit slope stability with beneficiation optimization of weathering-crust ores. The novelty of the research lies in the justification of rational pit-wall parameters based on a coupled 3D geological–geotechnical model implemented in the Micromine environment. Structurally disturbed zones were identified and subjected to detailed stability analysis using numerical modeling techniques. Particular emphasis was placed on the delineation of geotechnical domains and factor-of-safety evaluation in Slide2, which enabled refinement of design solutions and optimization of slope geometry. Simultaneously, the study addresses processing challenges of refractory weathering-crust ores through the application of ultrasonic aerohydraulic desliming combined with a vibro-centrifugal separation device. Optimization of slope parameters resulted in a 30 Mt reduction in stripping volume, corresponding to a 16.7% economic gain. The proposed flowsheet achieved a concentrate grade of 948.89 g/t REEs with an overall recovery of 45.66%. The results confirm that integrating geomechanical design with process engineering provides a technically robust and economically efficient basis for REE deposit development.

The article presents experimental data on the electrochemical oxidation of vanadium-bearing ore with the aim of increasing the efficiency of vanadium extraction during subsequent hydrometallurgical processing. Three different charge compositions were studied during the preliminary oxidative roasting stage, differing in the type of oxidizers used: calcined soda, sodium chloride, and their mixture in a mass ratio of 9:1. Electrochemical oxidation was carried out in a sulfuric acid medium using a membrane electrolysis cell equipped with an MK-40 type diaphragm. Experimental studies were conducted by varying key technological parameters: H2SO4 concentration (5–15%), solid-to-liquid phase ratio (1:2–1:5), temperature (25–85 ◦C), process duration (0.5–3 h), and current density (100–1000 A/m2 ). It was found that preliminary roasting promotes the conversion of vanadium into higher oxidation states, predominantly V5+, which significantly increases its solubility during subsequent electrochemical treatment. For the first time, the kinetic patterns of electrochemical vanadium leaching were identified, as well as the limiting mechanism of the process, associated with the formation of poorly soluble oxide films on the ore surface. Optimization of the electrochemical oxidation parameters allowed us to achieve vanadium extraction into solution up to 92%.

Industrial technologies for processing tungsten concentrates using soda roasting or autoclave leaching are based on the production of alkaline sodium tungstate solutions that contain impurities such as silicon, phosphorus, arsenic, and others. The purification of these solutions from impurities requires the neutralization of excess soda or alkali with inorganic acids, which leads to the formation of chloride and sulfate effluents that are subsequently discharged into waste repositories. An analysis was carried out on existing methods for the production and processing of sodium tungstate solutions using HNO3 and NH3, as well as extraction and sorption techniques involving anion exchange resins. Currently, processes such as nanofiltration, reverse osmosis, and electrodialysis are being applied for water purification and the treatment of sulfate and chloride effluents. These processes employ various types of industrially manufactured membranes. For the purpose of electrodialysis, a two-compartment electrodialyzer setup was employed using cationexchange membranes of the MK-40 (Russia) and EDC1R (China) types. The composition and structure of sodium tungstate, used as the starting reagents, were analyzed. Based on experiments conducted on a laboratory-scale unit with continuous circulation of the catholyte and anolyte, dependencies of various parameters on current density and process duration were established. Stepwise changes in the anolyte pH were recorded, indirectly confirming changes in the composition of the Na2WO4 solution, including the formation of polytungstates of variable composition and the production of H2WO4 via electrodialysis at pH < 2. The resulting tungstic acid solutions were also analyzed. The conducted studies on the processing of sodium tungstate solutions using electrodialysis made it possible to obtain alkaline solutions and tungstic acid at a current density of 500–1500 A/m2 , without the use of acid for neutralization. Yellow tungstic acid was obtained from the tungstic acid solution by evaporation.

Focuses on the processing of tungsten raw materials through various operations, including sintering, leaching, purification, and the production of technical tungstic acid. Modern research aims to enhance these processes, particularly the sintering of wolframite concentrates with alkali metal compounds and the leaching of concentrates and cakes. Experiments revealed that reactions between tungsten minerals and sodium carbonate from Akchatau ores commence at temperatures above 520–550 ◦C, intensifying between 750 and 850 ◦C. The concentrates were sintered at 750, 800, and 850 ◦C with a sodium carbonate excess coefficient of 1.05 to 1.2 to evaluate the effect on sodium tungstate extraction. Water leaching was conducted under a probabilistic–deterministic experimental design, analyzing five factors at four levels. Tungsten extraction was assessed based on solution density and the composition of the insoluble residue. Data processing established polynomial trends for tungsten trioxide extraction, and a material balance for sinter leaching was calculated from experiments using 100 g samples with a liquid-to-solid ratio of 2:1. The findings can be applied to improve tungsten processing technologies.