
In recent years, there has been an increased demand for nickel-cobalt-containing batteries, which in turn adds a lot of interest in the production of these metals in large volumes. Due to a contraction of the volume of nickel sulfide ores, the majority of producers consider laterite deposits as a potential source of nickel and cobalt. However, processing laterites by traditional pyrometallurgical methods is economically unprofitable. Research has shown that the use of combined and hydrometallurgical methods can be promising. This article is devoted to a review of the results of research and articles on the extraction of nickel and cobalt from laterite ores over the past 20 years. Current technological schemes for the production of nickel and cobalt using combined manufacturing processes are presented, as well as the results of scientific research on increasing the recovery degree of nickel and cobalt from low-grade refractory laterite ores using preliminary activating roasting, various leaching reagents, oxidizing agents, bacteria, etc. Growing interest in nickel production has also been observed in Kazakhstan and research work on the extraction of target metals from local laterite ores is being intensively carried out. According to the investors’ forecast, the first mining in the republic and full commissioning of nickel production are expected in 2025. © 2024, Ore and Metals Publishing house. All rights reserved.

In recent years, computer vision has emerged as a key technology for autonomous mobile robots and transportation systems, enabling their ability to perceive the environment and make real-time decisions. One of the most critical and widely demanded tasks is object detection, which is essential for navigation, collision avoidance, and the execution of mission-specific operations. This paper examines experimental studies of computer vision algorithms used for object detection in mobile robots. The focus is on the analysis and comparison of modern methods, including classical image processing algorithms and deep learning-based neural network approaches. The experimental study was conducted in a pipeline system to detect in-pipe defects, which requires high accuracy and robustness of algorithms given the limited computing resources of mobile platforms. Experiments were conducted using various object detector architectures (YOLO, SSD, Faster R-CNN) and lightweight models, such as MobileNet, designed for resource-constrained environments. Algorithm performance was evaluated based on accuracy and processing speed. The results of the study enable the identification of optimal solutions for integrating computer vision systems into mobile robots, ensuring a balance between detection quality and operational efficiency. Furthermore, the study explores the potential adaptation of these architectures for specialized scenarios, such as pipeline inspection, where detecting complex-shaped defects within confined spaces is required.

Zinc and lead are one of the most used metals in the world. The average annual growth rate of the zinc market is about 3.5%. Half of the zinc consumed in the world is used as electroplating, more than 30% is spent on the production of zinc alloys, including for the production of brass and bronze. At present, polymetallic ores are the main raw material for the production of lead and zinc. The production technology includes flotation enrichment of the initial ore raw material with subsequent pyrometallurgical or hydrometallurgical processing of the resulting concentrates. Unfortunately, the reserves of well-enriched sulfide ores are declining, which leads to the need to involve mixed and oxidized ores in the production. Obtaining zinc is also a relatively expensive process, one of the stages of which is the roasting of zinc sulfide concentrates in a fluidized bed furnace using oxygen-enriched air blast. In this regard, technologies aimed at processing hard-to-cut oxidized lead-zinc ores, as well as improving the process of roasting in a fluidized bed, are topical and in demand today. The article presents the technology and method for processing oxidized lead-zinc ore, including high-temperature sulfidizing roasting of oxidized compounds of lead and zinc, the results of roasting carried out in the presence of a high-sulfur sulfidizing agent in the form of pyrite (sulfur content is 45.15%), at molar ratios of metal oxide to pyrite NZnO/NFeS2 and NPbO/NFeS2 equal to 0.1–0.14 for sulfidizing in an air-blown fluidized bed furnace at a flow rate of 10 to 20 l/min, at a temperature of 750–800 °C, with a roasting time of 30–45 minutes. As a result of sulfidizing roasting, the degree of sulfidization reaches 88%, and the subsequent extraction of zinc from the non-magnetic fraction into a froth product in an open flotation cycle is 90% with a content of 23.4% zinc.
The article provides an overview of modern methods of processing mining and metallurgical waste to obtain functional materials such as silicon, rare earth metals, nanoporous silica and other valuable components. The technologies of processing and purification, including hydrometallurgical and pyrometallurgical processes, as well as their applicability to various types of waste generated in the mining and metallurgical complex are considered. Special attention is paid to the environmental aspects and economic efficiency of waste recycling, as well as the possibilities of implementing waste-free processes that reduce environmental pollution. Examples of successful implementation of innovative technologies are given and prospects for the use of recycled materials in various industries are described. The authors emphasize the importance of implementing waste-free processes to reduce environmental pollution. The article also discusses methods for the extraction and processing of silicon and silica, which can significantly improve the properties of the final products. Innovative technologies for processing waste from mining and metallurgical production contribute not only to reducing the volume of waste but also to the creation of new economically profitable materials. The study aims to draw attention to the importance of waste recycling and demonstrates the potential of their use as valuable raw materials, which contributes to sustainable development and efficient use of natural resources. The authors also discuss the prospects for further development of recycling technologies, including the development of new methods and optimization of existing processes, which will increase efficiency and reduce waste recycling costs.
The article discusses the forces that arise when a TE-33A diesel locomotive moves through a switch. The analysis of dynamic loads acting on rail threads, crosspieces, and other switch elements is carried out. The purpose of this article is to determine the efforts of the TE-33A diesel locomotive acting on the main elements of the railway track switch. The measurements were carried out in accordance with the requirements using a strain gauge measuring and computing complex consisting of certified and verified measuring instruments from the world's leading manufacturers. As a result of theoretical analysis and experimental studies, the lateral and vertical forces transmitted by the wheels to the inner and outer rails of the transfer curve were determined when the TE-33A locomotive was moving along the R65 mark 1/11 switch. Possible causes of increased wear of the switch elements under the influence of the TE-33A diesel locomotive have been identified. Recommendations are proposed to reduce the negative impact on the switches, including optimizing driving modes. Based on the results obtained, diagrams of vertical and transverse forces were constructed, and indicators of the stress rate at maximum speed along the arrow of the locomotive in question were established.

The development of a country's economy largely depends on the pace and efficiency of construction work, which, in turn, is determined by the extent to which innovative technologies and techniques are used. This work is devoted to justification of the basic parameters and the development of a new working body for a machine for cutting joints in road surfaces. A design with cycloidal motion is proposed, which intensifies the destruction process due to the vibrational impact of the cutters on the material being processed. The use of such a working body provides a vibrational effect, increases the cutting speed, and reduces the energy consumption of the process. As a result of intensifying the interaction between the working body and the material, it was possible to reduce the energy consumption of cutting by 1.13 times, and increase productivity by 1.18 times compared to analogues.

Given the shortage of petroleum bitumen in the Republic of Kazakhstan, the use of local bitumen-containing rocks is becoming increasingly relevant, which requires the development of specialized mechanization tools. In this paper are discussed the special excavator buckets designed for year-round extraction of rocks with a bitumen content of up to 25%. The design features of the bucket that reduce resistance during digging and unloading are described. Calculations of resistance, chip thickness, operation duration, and productivity of the EO-4121 excavator at different temperatures and bitumen contents were performed. It is shown that unloading becomes more difficult when the bitumen content exceeds 18.2%. A comparison of the calculated and experimental data confirmed the high accuracy of the models used

In this study is presented an analytical mathematical model developed to determine the forces arising during the active penetration of machine working bodies into sticky rocks. The methodology is based on the method of element-by-element calculation of resistances, where the contact zone is divided into discrete prisms of material. As a result of the analysis, a final formula for the total penetration force is derived. This formula shows the dependence of the resistance force on the dimensions of the tool (thickness, depth, angle of sharpening) and the physical characteristics of the rock (internal friction, adhesion, stickiness). The model serves as a reliable engineering tool for the design and optimization of working bodies of earthmoving and mining equipment

The influence of the cutting angle on the resistance to the bulldozer blade burial during its movement, taking into account the one-sided stressed state of the soil, was studied in the research results of which are presented in this paper. It is established that the resistance to deepening is significantly reduced when the machine is moving, which allows using smaller cutting angles without increasing the energy consumption. Constructive features and kinematics of the working equipment are considered, including a promising parallelogram scheme, which provides automatic reduction of the cutting angle during deepening. Calculations of the resistance of the blade penetration into the ground, and experimental data confirming the cutting force reduction up to 7%, for each degree of angle reduction, are given. It is determined that the optimum cutting angle is 30-40°. The obtained results can be used to increase the productivity of bulldozers and optimize the design of their working equipment
Metal pollution from metallurgical emissions poses serious environmental and public health risks in Kazakhstan. A replicated pot-culture experiment (n = 4) in a completely randomized design under controlled phytotron conditions evaluated biomass production and metal accumulation in six crop and forage species, alfalfa (Medicago sativa), amaranth (Amaranthus spp.), corn (Zea mays), mustard (Brassica juncea), rapeseed (Brassica napus), and sunflower (Helianthus annuus); three ornamental species, purple coneflower (Echinacea purpurea), marigold (Tagetes spp., ‘Tiger Eyes’), and sweet alyssum (Lobularia maritima); and three native wild plants, greater burdock (Arctium lappa), horse sorrel (Rumex confertus), and mug wort (Artemisia vulgaris). Plants were grown in soils collected from the Qarmet industrial zone in Temirtau, central Kazakhstan. Initial soil analysis revealed substantial mixed-metal contamination, ranked as Mn > Ba > Zn > Sr > Cr > Pb > Cu > Ni > B > Co. Mn reached 1059 mg·kg−1, ~50-fold higher than B (22.7 mg·kg−1). Ba (620 mg·kg−1) exceeded FAO/WHO limits sixfold, Zn (204 mg·kg−1) surpassed the lower threshold, and Pb (41.6 mg·kg−1) approached permissible levels, while Cr, Cu, Ni, Co, and Sr were lower. Biomass production varied markedly among species: corn and sunflower produced the highest shoot biomass (126.8 and 60.9 g·plant−1), whereas horse sorrel had the greatest root biomass (54.4 g·plant−1). Root-to-shoot ratios indicated shoot-oriented growth (>1–8) in most species, except horse sorrel and burdock (<1). Metal accumulation was strongly species-specific. Corn and marigold accumulated Co, Pb, Cr, Mn, Ni, Cu, B, and Ba but showed limited translocation (transfer function, TF < 0.5), whereas sunflower, amaranth, and mug wort exhibited moderate to high translocation (TF > 0.8 to <1) for selected metals. Corn is recommended for high-biomass metal removal, marigold for stabilization, sunflower, horse sorrel, and mug wort for multi-metal extraction, and amaranth and coneflower for targeted Co, Ni, and Cu translocation, supporting sustainable remediation of industrially contaminated soils.