
The object of this study is to robotize the technological operation of removing the oxide film from the surface of a magnesium melt poured into continuously moving molds of a casting conveyor for the production of commercial magnesium. To robotize this technological operation, it is proposed to use a two-armed manipulation robot with a spherical coordinate system, which has six degrees of mobility. Software trajectories have been developed according to the degrees of mobility of the manipulation robot in terms of position, speed, and acceleration to perform the technological operation of removing the oxide film from the surface of the magnesium melt poured into the moving molds of the foundry conveyor. Programmed trajectories are described by quadratic polynomials that satisfy restrictions on the values of the generalized coordinate, velocity, and acceleration. These limitations are determined by the design features and energy capabilities of the degrees of mobility drives of the manipulation robot. Programmed trajectories along the first and second degrees of freedom compensate for the continuous movement of the molds of the foundry conveyor. Programmed trajectories along the third and fourth degrees of mobility enable the collection of the oxide film from the surface of the magnesium melt. Programmed trajectories along the fifth and sixth degrees of freedom enable the discharge of the collected oxide film into a special container. The reliability of the developed programmed trajectories is confirmed by the simulation results using MATLAB version R2015b. Based on the results, a cyclogram for controlling a manipulation robot has been constructed to perform the technological operation of removing the oxide film in the production of commercial magnesium. The results could be used in the robotization of technological processes for removing the oxide film in the production of commercial magnesium or similar foundries. © 2024, Authors. This is an open access article under the Creative Commons CC BY license

This paper was performed using geometry and interactive motion (GIM) software, a learning and research software designed to facilitate the kinematic analysis and synthesis of planar mechanisms. This study presents an analytical and geometric approach to the synthesis of planar four-bar linkages for precise path generation using sixth order connecting coupler curves. Emphasis is placed on defining linkage configurations that enable a coupler point to pass through a set of three, four, or five user-defined precision points. The methodology integrates classical kinematic principles, Roberts' theorem, and focal circle theory to identify double points and optimize the trajectory of the coupler. Using complex number representations and algebraic formulations, the equations governing coupler motion are derived and applied to various linkage types, including crank-rocker, double-rocker, and limit mechanisms. Parallelogram constructions and focal circles are used to detect critical configurations and analyze the continuity and self-intersections of coupler paths. Computational simulations validate the synthesis approach across different configurations, highlighting trade-offs between accuracy and mechanical feasibility. The results demonstrate the applicability of the method in advanced motion control tasks such as robotic arms, dwell mechanisms, and function generation. This work contributes to the field of kinematic synthesis by offering a rigorous framework for linkage design with enhanced precision, reliability, and versatility. © The Author(s) 2026. Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits the use, sharing, adaptation, distribution and reproduction in any medium or format, as long as appropriate credit to the original author(s) and the source is given by providing a link to the Creative Commons license and changes need to be indicated if there are any. The images or other third-party material in this article are included in the article's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

The object of this study is the technological operation of removing the oxide film from the surface of the metal melt, foundry production of commercial lead, zinc. To carry out the robotization of this technological operation, it is proposed to use a manipulation robot with a spherical coordinate system. A kinematic structure of a manipulation robot with six degrees of mobility and two arms is proposed. On the first arm of the manipulation robot, a movable blade is fixed, and on the second arm, a rotary blade is fixed. With the translational movement of the first hand, the movable blade rakes the oxide film onto the rotary blade. Further, the oxide film collected on the rotary blade is thrown into a special container with a rotational movement. Restrictions are introduced on the values of generalized coordinates, velocities, and accelerations for each degree of mobility of the manipulation robot. Taking into account these limitations, for the implementation of this process, software trajectories have been developed for the degrees of mobility of the manipulation robot, which are approximated by quadratic polynomials. Each program movement is divided into three sections, in the first section acceleration with a given acceleration is carried out, in the second section movement with a given speed, in the third section braking with a given acceleration. To assess the reliability of the developed software trajectories, simulations were carried out in the MatLab software environment, version R2015b. The resulting graphs of program trajectories coincide with the calculated values of the generalized coordinates, time intervals, speeds, and accelerations of change in the generalized coordinates in terms of the degrees of mobility of the manipulation robot. The period of time required to remove the oxide film is 15.88 s. On the basis of the results obtained, a cyclogram for controlling a manipulation robot was built to perform the technological operation of removing the oxide film in the production of commercial lead, zinc
Целью данного исследования является применение методов искусственного интеллекта (ИИ), в частности искусственных иммунных систем (ИИС), для разработки оптимальной стратегии управления многопараметрической системой управления. Исследуются два конкретных подхода к управлению в промышленности: интегрально-пропорционально-дифференциальное (ИПД) и пропорционально-интегрально-дифференциальное (ПИД) управление. Мотивацией для использования этих вариантов ПИД-регуляторов является их функциональная реализация в современных промышленных контроллерах, где они обеспечивают точное управление технологическим процессом. Результаты исследования представляют собой новое решение задачи синтеза управления для промышленной системы.
В данном исследовании представлен устойчивый и адаптивный подход к переработке полезных ископаемых. Была разработана гибридная интеллектуальная система управления для обогащения мелкодисперсной хромитовой руды в отсадочной машине. Цель состоит в повышении эффективности разделения и снижении потерь хрома за счет оптимизации параметров процесса в реальном времени при переменных условиях подачи. Метод учитывает колебания состава руды путем интеграции трех компонентов: физического моделирования движения частиц, регрессионного анализа и прогнозирования на основе нейронной сети. Уровень слоя отсадочной машины и частота пульсаций используются в качестве управляющих переменных, а содержание Cr₂O₃ в подаваемом сырье (формула представлена) рассматривается как возмущение. Нейронная сеть прогнозирует содержание Cr₂O₃ в концентрате ( формула представлена) и в отходах (формула представлена)), представляющих собой , соответственно, богатую хромитом и пустую фракцию. Оптимизация выполняется с использованием алгоритма внутренней точки с ограничениями. Модель демонстрирует высокую точность прогнозирования со среднеквадратичной ошибкой (MSE) ниже 0,01.
В данном исследовании предлагается интеллектуальный алгоритм управления для промышленных процессов с множественным входом и множественным выходом (MIMO). Этот алгоритм основан на интеграции цифрового двойника (DT), модельного прогнозирующего управления (MPC), генетического алгоритма (GA) и нейронной сети (NN). Разработанная архитектура использует гибридную схему MPC, включающую дополнительную ветвь коррекции на основе нейронной сети. Рабочий процесс включает предварительную обработку входных данных, линеаризацию рабочей точки и обучение нейронной сети, вычисление оптимальной последовательности управления на скользящем горизонте, управление с обратной связью и адаптацию на основе ошибки прогнозирования. Этот инновационный гибридный закон управления использует линейную модель пространства состояний в качестве базового предиктора и компактную надстройку нейронной сети для компенсации неучтенных нелинейностей. Генетический алгоритм ищет оптимальную последовательность управляющих воздействий, соблюдая ограничения процесса и обеспечивая стабильное использование коррекции на основе нейронной сети.

Freeze-drying of camel milk is time-consuming due to its high density, protein, and fat content, which limits industrial application and increases energy demand. In this study, ultrasonic treatment (UT) and homogenization were applied as pretreatments prior to freeze-drying. A full factorial design (24) was used to evaluate process factors. Experimental trials were combined with mathematical modeling based on heat and mass transfer equations (Fourier’s law, Fick’s law, and dimensionless criteria Re, Pr, Nu). Pretreatment significantly improved drying efficiency: the drying time of camel milk was reduced from 28 h (control) to 22 h (treated samples), corresponding to a 21% decrease. Protein content and solubility were enhanced, while residual moisture decreased to 3–4%. The developed equations accurately predicted sublimation rates and drying kinetics, with R2 = 0.95 confirming high model reliability. The integration of ultrasonic treatment and homogenization into freeze-drying provides a viable strategy for reducing drying time and improving product quality of camel milk. The established criterion equations and models support process optimization and industrial application.

Vacuum freeze-drying is a preferred method for converting mare’s milk into a shelf-stable powder while retaining its nutritional and sensory qualities. However, the process remains time-consuming and energy-intensive. This study presents a validated three-dimensional numerical model that simulates conjugate heat- and mass-transfer during vacuum freeze-drying under industrially relevant conditions. The governing equations for heat conduction, water-vapour transport (Darcy’s law), and latent-heat removal were solved in COMSOL Multiphysics 6.3 using the Deformed Geometry interface to track phase-front motion without remeshing. Simulations were performed on a 50 × 45 × 0.7 cm slab frozen to -50 ℃ with a shelf temperature of -20 ℃ and chamber pressure ranging from 15 to 35 Pa. Validation was conducted in a 0.45 m2 pilot dryer using centre-line temperature measurements and gravimetric moisture-loss data. The model reproduced experimental temperature profiles (R2 = 0.96) and predicted sublimation-front motion within 4% of image-based observations. Thinner samples (3 mm vs. 7 mm) and lower pressures (15 Pa vs. 35 Pa) significantly reduced drying time, though gains diminished below 15 Pa. This model offers a practical framework for optimising freeze-drying conditions and is extendable to other porous food and biopharmaceutical products. © The Author(s) 2025. This article is licensed under a Creative Commons Attribution 4.0 International License, which permits the use, sharing, adaptation, distribution and reproduction in any medium or format, as long as appropriate credit to the original author(s) and the source is given by providing a link to the Creative Commons license and changes need to be indicated if there are any. The images or other third-party material in this article are included in the article's Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.
Показано 233–240 из 1222