
Introduction. The article presents the results of the research strategy for the development of mountainous territories of Kazakhstan. The study of the ossibilities of developing the energy system of mountainous territories is shown on the example of the city of Almaty (Kazakhstan). Materials and Methods. To study the energy efficiency indicators of enterprises in the manufacturing industry, Almaty Heavy Machinery Plant (AHMP) was selected as one of the largest machine-building enterprises in Almaty. Results. It is shown that in the conditions of supplying the water supply system with industrial water from mountain rivers, hydro turbines can be used. It was found that such hydro turbines can be placed in water supply pipelines of production shops. Discussion. An assessment was made that showed that the electricity generated by them can be used to power their own equipment, as well as to supply electricity to the general network. Conclusion. The obtained average efficiency of the hydro turbine of 39 % allows us to calculate the possible generation of electricity in real conditions up to 11 kW, while the declared capacity was 16 kW. Resume. If we consider the tasks of energy saving in production, we can confidently predict that the generation of electricity from the developed hydro turbine will reduce the total electricity consumed from the grid. Suggestions for practical applications and directions for future research. The mini-hydroelectric power station developed and presented in this work can be used in water supply systems of industrial enterprises located in mountainous regions. This system can contribute to increasing the energy efficiency of enterprises. In the future, it is planned to scale these mini-hydroelectric power stations and make smaller and larger units for use in larger and smaller enterprises. © 2024 North Caucasian Institute of Mining and Metallurgy, State Technological University. All rights reserved.

Drought stress limits plant survival and yield in arid regions. Uncovering the molecular mechanisms of drought tolerance is key to developing resilient crops. This study used Arabidopsis thaliana as a model to perform an in silico analysis of miRNA–mRNA interactions linked to post-transcriptional drought response. Using the MirTarget program, 274 miRNAs and 48,143 gene transcripts were analyzed to predict high-confidence miRNA–mRNA interactions based on binding free energies (−79 to −129 kJ/mole). Predicted binding sites were located in the CDS, 5′UTR, and 3′UTR regions of target mRNAs. Key regulatory interactions included ath-miR398a-c and ath-miR829-5p targeting ROS detoxification genes (CSD1, FSD1); ath-miR393a/b-5p and ath-miR167a-c-5p targeting hormonal signaling genes (TIR1, ARF6); and the miR169 family, ath-miR414, and ath-miR838 targeting drought-related transcription factors (NF-YA5, DREB1A, WRKY40). Notably, ath-miR414, ath-miR838, and the miR854 family showed broad regulatory potential, targeting thousands of genes. These findings suggest the presence of conserved regulatory modules with potential roles in abiotic stress tolerance. While no direct experimental validation was performed, the results from Arabidopsis thaliana provide a useful genomic framework for hypothesis generation and future functional studies in non-model plant species. This work provides a molecular foundation for improving drought and salt stress tolerance through bioinformatics-assisted breeding and genetic research. © 2025 by the authors.

Purpose. The research aims to study wastewater treatment technology using electrical discharge at the Aktogay field in Kazakhstan to assess its effectiveness in reducing heavy metal concentrations and improving water quality. Methods. Laboratory tests were conducted on a specially designed experimental setup operating in the voltage range from 15 to 100 kV and frequencies from 50 Hz to 10 kHz. Physical-chemical parameters of water (pH, electrical conductivity, temperature), concentrations of heavy metals (copper, zinc, cadmium) before and after treatment were measured. Mathematical models were used to describe the precipitation processes and to assess the purification efficiency. Findings. Electrical discharge technology has been found to achieve a purification rate of up to 97.5% for copper, 97.3% for zinc and 96% for cadmium. At optimal parameters (15 kV, 10 kHz), heavy metal concentrations are reduced to levels that comply with World Health Organization standards. Improvement of physical characteristics of water (colour, odour, electrical conductivity) confirms the high efficiency of the method. Originality. For the first time, an innovative wastewater treatment methodology based on electrical discharge technology, implemented using a specially designed device, has been developed and tested. Mathematical models of heavy metal removal processes that describe the kinetics and dynamics of pollutant precipitation have been proposed and experimentally confirmed. Practical implications. The obtained results demonstrate a high potential for the industrial application of electrical discharge technology for treatment of wastewater generated during the processing of mineral raw materials at the Aktogay mine. Implementation of this technology will improve the environmental safety of production, while reducing operating costs and ensuring the possibility of water reuse. © 2025. A. Abdykadyrov et al.

The article presents a method of complex kinematic analysis of a mechanical wind turbine system. Input data, such as the speed of rotation of the input shaft of the gearbox, for the multi-criteria analysis of the planetary multiplier of the wind turbine were obtained from the results of computer simulation of the air flow. The fundamentals of the torque method were used to study planetary compound gears (PСG), called a multiplier. The variants of kinematic schemes of composite planetary transmission are analyzed in order to determine the most optimal distribution of the energy flow. The torque method allows not only kinematic analysis (determining the ratio of speeds), but also power analysis (determining the direction and magnitude of internal power flows), as well as determining efficiency. Relatively simple formulas for calculating the ratio of speeds and efficiency made it possible to carry out multi-purpose optimization of the parameters of the considered PСG. As a result of the analysis, the most optimal scheme of a composite planetary gearbox was determined, taking into account the kinematics of the airflow on the wind turbine wheel. © 2024, National Academy of Sciences of the Republic of Kazakhstan. All rights reserved.

Nanoparticles are widely used in Pickering emulsions, but their hydrophilic nature often limits interfacial effectiveness. This study explores a novel chemical etching method using the strong reductant sodium borohydride (NaBH₄) to enhance the interfacial properties of silica nanoparticles, improving oil recovery through more efficient Pickering emulsification. Characterization confirms surface etching through TEM and XPS, showing a rougher surface and a hydrodynamic size of 164.43 nm for etched silica, compared to 197.74 nm for bare silica. The etched silica nanoparticles exhibit increased hydrophobicity, as evidenced by FT-IR and contact angle measurements (θ = 75 ± 1° for etched silica vs. θ = 20 ± 1° for bare silica). At 500 ppm, modified silica nanoparticles facilitate Winsor emulsions I and II, with etched silica producing smaller, more stable droplets. Increasing the concentration to 2500 ppm reduces droplet size and tightens distributions, especially with etched silica, enhancing emulsion stability due to stronger interfacial layers, non-spherical shape, and lower bending resistance, as shown by desorption energy values of ⁓ 3.91 × 10−18 J for bare silica and ⁓ 3.49 × 10−16 J for etched silica. Pore-scale experiments demonstrate that surface-etched silica nanoparticles improve oil displacement and reduce residual trapping by promoting oil-in-water emulsions, outperforming bare silica due to stronger mechanical interactions, higher negative charge, and increased disjoining pressure (−4.81 × 10−4 Pa vs −8.38 × 10−4 Pa). This innovative modification approach, previously unexplored in oil recovery, offers a new pathway for enhanced oil mobilization and emulsion stability, with potential for broader applications in wastewater treatment, catalysis, and pharmaceuticals. © 2025 Elsevier B.V.
A wide range of applications such as healthcare, human comfort, agriculture, food processing and storage, and electronics manufacturing also require fast and accurate measurement of humidity and temperature. Optical fiber-based sensors have several advantages over electronic sensors, and much research has been conducted in this area in recent years. This paper describes the current trends in fiber optic temperature and humidity sensors. The evolution of optical structures aimed at humidity detection is presented, as well as a new design of an optical sensor used for this purpose. The main methods of humidity determination using fiber-optic laser reflection based on Optical fiber humidity sensor (FPI) were analyzed and experimental results were obtained. Based on temperature-sensitive strain variation, a method for temperature determination based on the specific spectral back-reflection effect of fiber Bragg gratings (FBGs) is considered. Experimental analyses were conducted on the light reflection of humidity-sensitive agarose using optical fibers based on the Fabry-Perot Interferometer (FPI). It exhibits a good linear response to relative humidity, ranging from 25 % to 95 %. During temperature measurement, the deformation changes of the Fiber Bragg Grating fibers showed excellent performance, ranging from –5 °C to 70 °C. New structures, such as resonators, are being explored to improve the resolution of fiber optic temperature and humidity sensors. In addition, recent studies on polymer optical fibers show that the sensitivity of this type of sensor has not yet been achieved. Thus, materials sensitive to humidity and temperature still need to be investigated to improve sensitivity and resolution Copyright © 2024, Authors. This is an open access article under the Creative Commons CC BY license

Urbanism principles in the context of the UK have significantly changed its urban public realm since the 1980s to shape a “world-class” public realm by welcoming high-income groups. However, there are still limited investigations into the performative role of the public realm. Therefore, the research aims to ask what the social impact of the equitable public realm is for every citizen. These findings will be archived through morphological mappings, observation, and photographing. While the research confirms that “world-class” public realms in cities are rather exclusive than inclusive, there is a framework for potential urban transformations. © 2023 Russian Academy of Architecture and Construction Sciences, Vostoksibacademcenter. All rights reserved.

This work presents a novel, cost-effective method for synthesizing AlxGa1−xAs nanowhiskers on a GaAs surface by electrochemical deposition. The process begins with structuring the GaAs surface by electrochemical etching, forming a branched nanowhisker system. Despite the close resemblance of the crystal lattices of AlAs, GaAs, and AlxGa1−xAs, our study highlights the formation of nanowhiskers instead of layer-by-layer film growth. X-ray diffraction analysis and photoluminescence spectrum evaluations confirm the synthesized structure’s crystallinity, uniformity, and bandgap characteristics. The unique morphology of the nanowhiskers offers promising implications for solar cell applications because of the increased light absorption potential and reduced surface recombination energy losses. We conclude by emphasizing the need for further studies on the growth mechanisms of AlxGa1−xAs nanowhiskers, adjustments of the “x” parameter during electrochemical deposition, and detailed light absorption properties of the formed compounds. This research contributes to the field of wideband materials, particularly for solar energy applications, highlighting the potential of electrochemical deposition as a flexible and economical fabrication method. © 2023 by the authors.
Показано 1209–1216 из 1222