
This study examined the suitability of polyethylene terephtal (PET) waste to provide an alternative modification to bitumen and reduce waste accumulation. The chemical structure and physical properties were evaluated for modified bitumen with different PET flakes content from 2 to 10 %. The effect of PET waste content on bituminous systems was analyzed using IR and 1H NMR spectroscopy, differential thermal (DTA) and thermogravimetric (TGA) analyses. The study of change in the microstructure as a result of bitumen modification was carried out using atomic force microscopy (AFM). Regularities of changes in the structural-group composition of bituminous binders after their modification with PET waste have been established. It is noted that the chemical interaction of the base bitumen with PET flakes occurs due to the formation of associative bonds between the oxygen-containing components of the modifier and bitumen. The influence of the modifier on the physical and mechanical properties was evaluated using standard methods (penetration, extensibility and softening point). Based on the physical and mechanical properties of bitumen, such as needle penetration depth (penetration), ductility and softening point, it was found that the optimal dosage of PET waste in terms of asphalt binder characteristics is 3 %. It has been established that PET waste and original bitumen interact both at the chemical and physical levels and can be considered as a suitable alternative for changing the properties of bituminous binders. Thus, the obtained samples of modified bituminous binders have improved physical and mechanical properties, which makes it possible to produce high-strength asphalt concrete pavements based on them © 2022. Authors. This is an open access article under the Creative Commons CC BY license
Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role in the development of the industrial complex and the production sector, and the surfaces of transport roads should be of high quality and have a long service life. Road infrastructure, like all infrastructure, requires preservation, maintenance and repair. There are special requirements for roadways that must be observed during construction or repair. The uncertainty of the composition, temperature sensitivity and viscoelastic characteristics of road materials make the structural analysis of pavement very difficult compared to other civil structures, such as bridges, tunnels and buildings. For this reason, the question of how to improve fiber sensors based on fiber Bragg grating (FBG) arose. The novelty of this study is to modernize fiber sensors based on FBG so that they display deformation, stress and displacement, temperature and other parameters with much greater accuracy, which would provide a reliable scientific basis for modifying the theory, as well as the use of a fiber sensor based on FBG for simultaneous measurement of deformation and temperature when monitoring the road surface. This article is devoted to a detailed study of the use of fiber-optic sensors (FOS) based on fiber Bragg grating for road surface monitoring. Such a fiber sensor, consisting of a fiber Bragg grating and a pair of grids, can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load and subsidence of soil and implement road safety and stability measures in a timely manner to evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results was about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring and designing road surfaces and in general transport infrastructure. © 2023 by the authors.

The issue of housing for humans has been extensively studied and remains highly relevant. While multi-story buildings in both large and small cities have addressed the need for residential accommodations, key aspects essential to ensuring comfortable living and human activity have often been neglected. A potential solution lies in the renovation of existing structures to enhance housing quality while preserving the original framework. This paper aims to explore the relationship between renovation approaches and the structural systems of residential buildings. It examines case studies of building renovations utilizing various materials, highlighting their features and applicable solutions. The analysis includes examples from multiple countries with diverse social, economic, and climatic conditions. Renovation is defined in this study as the process of modernizing residential buildings and their surrounding areas. Through an evaluation of architectural strategies employed in building renovations, the study identifies general trends and principles applicable to the refurbishment of standard residential structures. Based on these findings, the authors propose recommendations for renovation strategies tailored to different structural types. The outcomes of this research offer a framework for implementing revitalization projects, urban regeneration efforts, and building adaptation initiatives. © 2025 by authors, all rights reserved.
The need to remove radioactive iodine from water extends beyond the liquid radioactive waste treatment in the nuclear industry, as it can also be found in hospital wastewater and reach wastewater treatment plants. However, it remains a challenge affected by diverse iodine speciation, which includes anions and neutral forms. Recent developments in new carbon materials are offering new opportunities to capture radioactive iodine species from aqueous and gas phases. But how are they made, how feasible is their use, and how effective can they be? Do they outperform traditional carbon materials such as activated carbon? This review, for the first time, assesses current developments in preparing adsorbents for removing iodine species, including nanocarbons. Specifically, their synthesis, properties, maximum extraction capacity, and sorption mechanisms are discussed. The most effective biomass-based carbon for iodine removal was found to be chemically activated (with KOH) sunflower hydrochar with highly developed porosity and a surface area >2000 m2/g. Its capacity achieved 6.46 g of I2/g adsorbent. A similar level of uptake was demonstrated by KOH-activated hydrochar made from cellulose diacetate. The range of nanocarbons studied for this application did not outperform biomass-activated carbons. The regeneration of adsorbents, their scalability, current gaps in understanding the mechanisms of iodine species uptake, and the need to achieve their practical application have been discussed. The purpose of the review is to extract new knowledge from relatively new carbon nanomaterials, nanocomposites as well as traditional carbon sorbents that will inform the preparation of effective sorbents for upscaled applications such as the treatment of radioactive effluents from hospitals or liquid radioactive waste produced in the nuclear fuel cycle. © 2024 Elsevier Ltd

Generative potential and thermal maturity for Upper Palaeozoic source rocks from the south-eastern edge of Precaspian Basin were determined using Rock–Eval. A high hydrocarbon source rock generative potential and high degree of thermal maturity for the Lower Permian, Mid-Carboniferous strata have been revealed based on 39 rock samples. TOC values of 0.4–5.5% have been obtained for mature source rocks. Integrated geochemical analysis determined from Rock–Eval studies combined with 1D basin modelling was utilized in order to reconstruct thermal evolution for the Upper Palaeozoic source rocks. Calibrated 1D models for three wells had been constructed to understand petroleum system. For two deep exploration wells (Nur-1 and Tassym SE-1), which penetrated pre-salt strata at the depths of 5.7 and 7 km, respectively, the impact of salt diapirism on timing of maturation was modelled. Type II kerogen was used, which is based on previous palaeogeographic studies. The stratigraphic framework and major stages of geodynamic evolution were analysed. Salt-related structural traps in post-salt strata have been described based on 3D seismic data, and additional intra-salt sediment packages have been delineated. Discovered producing oil fields in the Upper Triassic and Jurassic–Cretaceous stratigraphic sections are mainly confined to the four-way dip structural closures above the steep flanks of salt structures. Based on burial and thermal modelling, the maturation and generation behaviour of kerogen Type II below salt-related minibasins and close to thick salt diapirs were inferred. For Lower Permian SR with type II kerogen, the generation peak (maturity over 50%) occurs in Middle to Late Jurassic. For predominantly carbonate and terrigenous-carbonate Mid-Carboniferous marine SR, generation peak occurs earlier below salt withdrawal minibasins. Implications for deeper hydrocarbon prospectivity were made for the study area, and methodology for evaluating hydrocarbon potential adopting 1D basin modelling technique and geochemical data is presented. © 2022, The Author(s).

Purpose. To justify and develop the theoretical bases of the formation and operation of the container technology for moving mining mass from quarries, which ensures a reduction of economic and energy costs, as well as damage to the environment during the extraction of mineral resources. Methodology. The work used complex research methods, including analysis and scientific synthesis of scientific and technical information; theoretical research; methods of mathematical and computer modeling, and design developments. Findings. The analysis of existing technologies for openpit mining and the current state of mining indicates an urgent need to develop new resourcesaving technology and environmentally friendly technologies for moving rock mass for openpit mining. A new technology for container transportation of rock mass in containers is proposed without the construction of additional transport communications in the quarry and has technological and energysaving advantages. Originality. The scientific novelty of the research consists of an integrated and systematic approach to assessing the energy efficiency and environmental safety of the proposed set of equipment for container technology for transporting rock mass. Practical value. In this work, special attention is paid to the problem of the formation and effective use of a new resourcesaving and environmentally friendly container technology for moving rock mass from deep quarries. These advantages are simultaneous excavation of rocks, transportation of rocks over the shortest distance, low container packing ratio, and mobility of a complex of lifting machines, which will reduce energy consumption and the cost of transporting rock mass. A transport complex has been developed to ensure the reliable operation of lifting and transport machines.

This paper presents the results of determining the parameters of tritium transfer processes in lithium ceramics Li2TiO3 under reactor irradiation conditions. Analysis of sections with a short-term decrease in reactor power allowed numerical determination of the Arrhenius parameters of tritium diffusion (pre-exponential factor and activation energy) based on comparison with in situ experimental data. The obtained values of activation energy (70.2–74.7 kJ/mol) and pre-exponential factor (0.9–2.1 × 10−8m2/s) demonstrate growth with increasing fluence, which is explained by the accumulation of radiation defects in ceramics. A linear dependence was established between D0 and Ea, corresponding to the Mayer–Noldel rule. Unlike previously conducted studies based on a phenomenological approach to assessing only the activation energy of diffusion, in this study, a complex model that takes into account temperature gradients, tritium generation, its diffusion, and release from the surface was used. The applicability of such an integrated approach to the analysis of in situ reactor experiments with lithium ceramics was confirmed, and allowed us to estimate changes in the tritium transfer parameters in lithium ceramics Li2TiO3 depending on the irradiation time. © 2025 by the authors.

Purpose. To analyze the development of landslide processes in the village areas, study the causes of the destruction of the coastline of Lake Alakol, and develop recommendations for coastal protection measures. To assess the impact of key geological, hydrological, and climatic factors on the intensity of abrasion processes and the dynamics of the coastline. Methodology. The methodology includes a comprehensive approach. Monitoring of the shoreline was conducted, covering the measurement of erosion speed and direction, evaluation of sediment volumes, analysis of changes in the coastline and geomorphological features. Computer modeling was used to predict destructive processes, considering multiple factors such as hydrological conditions, lithological composition of rocks, and climatic conditions. Retrospective analysis of long-term observation data and photographs revealed patterns in the development of shoreline changes. Findings. The changes in the shoreline of Lake Alakol are related to the complex interaction of natural and anthropogenic factors. The main causes of shoreline destruction were identified, including active landslides, wave erosion, and changes in the hydrological regime. Measures for shore strengthening were proposed: installation of breakwaters, slope reinforcements, planting vegetation, creation of artificial beaches, and other engineering measures. A program for predicting coastal destruction using mathematical models has been developed, which allows for effective planning of measures to protect them. Originality. The scientific novelty of this work lies in the integration of modern monitoring, analysis, and modeling methods to study the dynamics of coastal processes. This approach provides a deeper understanding of the causes of shoreline destruction and contributes to the development of optimal engineering solutions. Practical value. Recommendations are developed that can be used for strengthening the shores of Lake Alakol, as well as preventing exogenous geological processes (shoreline abrasion, landslides, landslips, collapses, gully formation, etc.) at other water bodies. © Alzhigitova M. M., Tileuberdi N., Zapparov M. R., Auyelkhan Y. S., Abdisseiit E. S., 2025
Показано 985–992 из 1222