
This article presents the effectiveness of the use of a new complex of aluminosilicomanganese ferroalloys as an oxygen-containing agent necessary in the production of steel and special alloys. The aluminum silicomanganese alloy is smelted using manganese ore and high-ash coal. In addition to the low cost of the melt, it provides deep purification of both aluminum, silicon and manganese, as well as low-carbon steels from non-metallic impurities. Aluminum silicomanganese is intended for investigation of electrical resistivity of charge materials for melting. Questions of research of specific electrical resistance of charge materials for the smelting of aluminosilicomanganese, in particular, high-ash coals, are considered. The measurements were carried out in the Tamman laboratory unit on a special combined experimental setup connected via converters. Studies on changes in the electrical conductivity of coal were carried out in the temperature range 25-1500°C at a heating rate of 15 deg/min. The main regularities of the formation of the electrical resistivity of charge materials depending on the temperature are determined. The proposed method of measurement makes it possible to obtain in-depth information about the physicochemical properties of charge materials. High-ash coal "Saryadyr", having a constant specific electrical resistance at high temperatures, can be achieved optimal melting mode.

In this paper, based on the results obtained, a general assessment of the integrated waste gas treatment technology of the TPP was carried out in terms of its technological and environmental-economic efficiency. The principal possibility of implementing the technology of cleaning waste gases from SO2 and NOx in a continuous mode is shown. When using the developed technology, the sulfur distribution in the gases obtained after purification is ~ 5%, and the main part – 95% is captured by the carbonate melt of alkali metals (Na, K, Li). Extraction of NOx into the melt is ~60%. Thus, already at the stage of chemical absorption of waste gases, favorable prerequisites are created for deep purification of gases from sulfur and toxic nitrogen compounds. An assessment of the economic efficiency of using the developed technology for burning coals with and without a high sulfur content has been carried out. A comparative analysis of the results of the cost of coal without sulfur with the cost of coal with a high sulfur content showed a significant economic effect, formed due to the difference in the cost of coal without sulfur and high sulfur content. Recommendations have been issued in relation to the conditions of small boiler plants operating on coal combustion, which will optimize the organization of the technology and use it in continuous operation.

The article presents the results of studies on the production of ferrosilicon, ferrosilicoaluminium and Fe-Si-Al ligatures when replacing steel chips with magnetite. The object of research was the carbonaceous rock of the Borly deposit. Thermodynamic modeling was carried out using the HSC-5.1, Chemistry software package of the Finnish metallurgical company Outokumpu, based on the principle of minimizing Gibbs energy, and experimental studies-electric melting in an arc furnace at 1000-1400°C begin to form. It was found that under equilibrium conditions, the interaction of Borly ash components with magnetite and carbon in the presence of silicon oxide with silicon-containing reduction products - Si, SiO, FeSi2, Fe3Si, FeSi, SiC; with an increase in the amount of carbon, the degree of silicon extraction in SiC increases. in the elemental state and decreases- in Fe3Si, FeSi; the degree of silicon extraction into the alloy increases, amounting to at 2000°C and 51% carbon, and the degree of silicon transition into the alloy also increases, amounting to 76.4% at 2100°C and 51% carbon. It is determined that, from Borly ash under equilibrium conditions, it is possible to obtain ferrosilicon grades FeSi15, FeSi25, FeSi45 and FeSi50 in the temperature range 1260-1860°C and ferrosilicoaluminium grades FS45A10 and FS45A15 in the temperature range 1930-2100°C. It has been experimentally established that ferrosilicon of the FeSi60 brand (68.7% Si, 1.3% Al) is formed from the conclusions of the electric melting of coal waste together with magnetite concentrate, quartzite and coke.

The availability of reliable data on the PVT properties of reservoir fluids plays a leading role in calculating the reserves of oil and gas reservoirs, estimating the oil recovery factor, well testing, numerical reservoir modeling and for making informed decisions in field development design. In practice, the results of field, laboratory and theoretical studies are used simultaneously to substantiate the properties of natural hydrocarbon mixtures. At each of the noted stages, specialists strive to increase the reliability of the data obtained and develop methods for their interpretation. Determining the properties of reservoir fluids of an oil field is a prerequisite for the effective use of various methods of influencing the bottomhole zone of wells, selection of equipment for well operation. The properties of reservoir fluids are determined by various thermobaric conditions and change depending on the current state of the reservoir and the characteristics of reservoir pressure changes. All known methods for determining the properties of formation fluids are divided into two groups: experimental and computational. Each of the groups has both advantages and certain disadvantages.

Work aim is to carry out geomonitoring of rock mass state, which provides for comprehensive accounting and analysis of all natural and man-made factors, as well as use of methods and control tools developed by authors.Work uses complex method, including: study of mining and geological conditions, structural features of rocks of deposits and conduct of mine surveying observations in mines based on innovative methods and means of geomonitoring developed by the authors. Research materials of geomechanical processes at the mines of Akzhal, Saryoba Sayak and others are presented during projects implementation of «Development of innovative methods for predicting and assessment of rock mass state to prevent technogenic emergencies» and «Comprehensive monitoring of slow deformation processes of the earth's surface during large-scale development of ore deposits of Central Kazakhstan», and also used in the educational process of Satbayev University. As a result of research: methodology for comprehensive assessment of rocks state has been developed, which makes it possible to consider features of geological structure of undermined strata and, thereby, improve quality of geomechanical support for mining operations; design of permanent forced centering point (FCP) for installation of high-precision instruments has been developed, which makes it possible to ensure speed and accuracy of centering, as well as to exclude use of tripods; scientifically substantiated possibility of predicting stress-strain state of rock mass in the studied deposits, i.e. it is possible to determine: tensile strength - σco; clutch - K; density - γ and strength of rocks - f according to the scale of M.M. Protodyakonov; composition of hardening solution from mining waste has been developed to increase stability of sections of ledges of quarry, which has high fluidity, adhesion to rocks and sufficient strength.

The article presents an innovative approach to the geometrization of ore bodies during exploration work based on geophysical and/or core studies in wells for the purpose of areal and thickness delineation of hydrogenetic ore mineralization. The method makes it possible to obtain more accurate contours of ore bodies with a minimal increase in the number of wells constructed for this purpose. The method can be used in planning and conducting exploration work on hydrogenetic deposits. On the example of reservoir-infiltration uranium deposits of the Shu-Sarysu uranium ore province located in South Kazakhstan, shortcomings in the geometrization of ore bodies using the traditional method of placing of geological exploration wells are demonstrated, as well as the shortcomings of the proposed in literature methods of ore geometrization and the main advantages of the proposed innovative approach. The developed method solves a number of significant problems in the subsequent planning and implementation of mining and preparatory work at hydrogenetic deposits, contributes to a significant increase in the accuracy of the geometrization of ore bodies and calculation of reserves, and increases the reliability and investment attractiveness of explored hydrogenetic deposits. This method can also be used to save money by reducing the number of wells being constructed, if used for an inverse problem in order to discharge placement of exploration wells in middle part of ores bodies in hydrogenetic fields with a dense drilling grid.

The agglomerate, as a raw material of blast furnace melting, must have such a set of properties that meets the requirements of the blast furnace process to the maximum extent. The quality of agglomerates is assessed by chemical composition, mechanical and physico-chemical properties A high-quality iron ore raw material for blast furnace melting is considered to be an agglomerate with a high iron content with a minimum content of harmful impurities, uniform in size with a minimum content of classes of more than 40 and less than 5 mm, a narrow range of softening and melting temperatures, having high reducibility and high strength. With the condition of the process of reducibility of dissimilar iron ore materials during agglomeration, it is necessary to consider the basic physico-chemical processes and thermodynamic conditions. The article describes the results of thermodynamic modeling of iron ore materials during the agglomeration process using the HSC Chemistry 5.10 program. Calculations are performed by the Reaction Equation subprogram. During the simulation, zonal technological processes of agglomeration of iron ore components of the charge are taken into account, since each zone corresponds to a certain phase formation due to physico-chemical processes corresponding to their temperature intervals. It is known, as a result implementing all the basic physico-chemical processes of agglomeration of iron ore materials; they should positively affect the quality of the resulting product. As a result, thermodynamic functions were determined in the temperature range of 25-1500°C for chemical reactions occurring in various zones of iron ore materials during the agglomeration process.

In recent years, methods of utilization of lumpy mineral raw materials of chromium production by encapsulation with modified sulfur from substandard grades of oil to obtain sulfur concrete have become increasingly popular. A significant amount of lumpy waste with a low content of Cr2O3 (~ 5-7% w/w) is formed when Kazakhstani chrome raw materials are processed by gravitation methods, and they can only be used as backfill in mine construction or as a component in building and road-building mixtures. Wastes from chromium deposits in Kazakhstan are located in close proximity to oil deposits in the Aktobe region, which are characterized by a high content of sulfur-containing heavy oils, which can be jointly disposed of in the form of sulfur concrete. Composite material - sulfur concrete is produced based on sulfur polymer binder - GreenCrete™ modified sulfur under GOST R 56249-2014. The possibilities of the sulfur-concrete composite formation process for the use of beneficiation tails of 10-160 mm class chromium raw material as inert materials have been studied. The characteristics of the samples obtained during the tests allow us to draw conclusions about the relatively successful encapsulation of chromium production waste in an amount of 15% by weight of the sample with the formation of sulfur concrete of the M400 class, while with a 10% content of materials for enrichment of chromium raw materials, the M500 indicator was achieved.