
Centrifugal pumps are extensively utilized across various industries, including water supply, agriculture, and energy, where they consume significant amounts of electricity. As demands for energy efficiency and reduced operating costs increase, enhancing pump efficiency has become crucial. This study focuses on optimizing the pump impeller geometry, which plays a vital role in minimizing energy losses. A hydraulic and hydrodynamic model was developed, alongside a parametric study based on numerical simulations (CFD), to analyze the influence of geometric parameters—specifically the angles and shapes of the blade’s inlet and outlet edges—on energy losses and hydraulic efficiency. The study utilized experimental data provided by the manufacturer for model verification. The results revealed that Ivanovsky’s method displayed deviations in the blade width at the leading edge and trailing edge of 25% and 43%, respectively, while Spiridonov’s method indicated deviations of 13% in the outer diameter (Formula presented.) and 27.5% in the blade width at the trailing edge. In contrast, the combined method proposed by the authors achieved high accuracy, with deviations under 9%. Additionally, parametric analysis identified two key parameters affecting the pump efficiency: the angle of the trailing edge and its shape. These findings underscore the necessity of optimizing the blade geometry to enhance the performance and energy efficiency of centrifugal pumps. © 2024 by the authors.

This paper is devoted to experiments on testing of the Sn-Li capillary porous system (CPS) under conditions of deuterium plasma irradiation, carried out at a plasma-beam installation (PBI). As a metal CPS matrix, molybdenum mesh was used. The paper presents a detailed description of the development of technology and procedure for the fabrication of the investigated sample, intended for plasma testing, as well as experiments on irradiation of Sn-Li CPS with deuterium plasma. As a result of the experiments performed, the dependences of the temperature of the investigated sample on the energy of the plasma contacting with the CPS, time dependence of the gas phase composition in the PBI chamber during irradiation of Sn-Li CPS with deuterium plasma, optical spectra depending on the temperature were obtained. Post-experimental material science studies with a sample of Sn-Li CPS were also performed and the results of microstructure, thermal and X-ray phase analysis were obtained. Analysis of the experimental data obtained showed that the energy of deuterium plasma precipitated on the Sn-Li alloy is re-emitted into the energy of optical radiation on the evaporating neutral atoms of lithium and tin. A complete evaporation of the alloy from CPS, during interacting with deuterium plasma, leads to partial destruction of the metal matrix of molybdenum. © 2023 Elsevier B.V.

Ceria-based H2O/CO2-splitting solar-driven thermochemical cycle produces hydrogen or syngas. Thermal optimization of solar thermochemical reactor (STCR) improves the solar-to-fuel conversion efficiency. This research presents two conceptual designs and thermal modelling of RPC-ceria-based STCR cavities to attain the optimal operating conditions for CeO2 reduction step. Presented hybrid geometries consisting of cylindrical–hemispherical and conical frustum–hemispherical structures. The focal point was positioned at x = 0, -10 mm, and -20 mm from the aperture to examine the flux distribution in both solar reactor configurations. Case-1 with 2 milliradian S.E (slope error) yields a 27% greater solar flux than case-1 with 4 milliradians S.E, despite the 4 milliradian S.E produces an elevated temperature in the reactor cavity. The mean temperature in the reactive porous region was most significant for case-2 (x = -10 mm) with 4 mrad S.E for model-2, reaching 1966 K and 2008 K radially and axially, respectively. In case-2 (x = -10 mm) for 4 mrad S.E, model-1 attained 1720 K. The efficiency analysis shows that the highest conversion efficiency value was obtained to be 7.95% for case-1 with 4 milliradian S.E. © 2023 The Author(s)

Oil spills on land pose significant environmental hazards, impacting ecosystems and human health. Effective detection and monitoring of these spills are critical for timely response efforts. This paper presents for the first time a ground truth dataset for onshore oil spill detection developed using Landsat imagery. The ground truth was implemented using aerial data. To demonstrate the utility of this dataset, we evaluated several state-of-the-art deep learning models, including DeepLabV3+, UNet, PSP-Net, DeepLabV3 and Mask2Former. Our experiments revealed significant insights into the models’ capabilities and limitations. Mask2Former and DeepLabV3+, in particular, showed the highest performance metrics. On the validation data, Mask2Former achieved an intersection over Union (IoU) of 72.69% and a F-score coefficient of 84.18%, while DeepLabV3+ achieved an IoU of 67.6% and a F-score coefficient of 80.67%. These results demonstrate the effectiveness of our dataset as a crucial tool for enhancing oil spill detection methodologies and advancing the application of artificial intelligence in ecological preservation and disaster management. ©The Author(s) 2024.

Layers of TiO2 nanotubes formed by the anodization process represent an area of active research in the context of innovative energy conversion and storage systems. Titanium nanotubes (TNTs) have attracted attention because of their unique properties, especially their high surface-to-volume ratio, which makes them a desirable material for various technological applications. The anodization method is widely used to produce TNTs because of its simplicity and relative cheapness; the method enables precise control over the thickness of TiO2 nanotubes. Anodization can also be used to create decorative and colored coatings on titanium nanotubes. In this study, a combined structure including anodic TiO2 nanotubes and SrTiO3 particles was fabricated using chemical synthesis techniques. TiO2 nanotubes were prepared by anodizing them in ethylene glycol containing NH4F and H2O while applying a voltage of 30 volts. An anode nanotube array heat-treated at 450 °C was then placed in an autoclave filled with dilute SrTiO3 solution. Scanning electron microscopy (SEM) analysis showed that the TNTs were characterized by clear and open tube ends, with an average outer diameter of 1.01 μm and an inner diameter of 69 nm, and their length is 133 nm. The results confirm the successful formation of a structure that can be potentially applied in a variety of applications, including hydrogen production by the photocatalytic decomposition of water under sunlight. © 2024 by the authors.

Wind power in Kazakhstan, following the global trend, continues to develop and there is an increase in the number of RES power plants. The development of wind energy involves the creation of large-sized and high-power installations. The rotors of wind turbines experience heavy loads on their design. Thus, the actual task and problem for the wind energy park of Kazakhstan is to reduce the load on the structure by regulating it during wind gusts. The use of a control system for the rotation of the blades makes it possible to significantly reduce the load on the structure. However, due to the non- linearity of the process and the difficulty of accurately measuring the wind speed, the blade turning control system must be designed with great care. This paper presents the development of a lever mechanical system for controlling the blades of a wind turbine, which makes it possible to secure the operation of a wind generator. The purpose of the study is to develop a 3D model of a lever control system and create an automatic control system for it. A three-dimensional study of the rotor in various states of the rotor was carried out. This dynamic computer model is proof of the functionality of the communication system. The transfer function of the entire control system is also determined and, based on experimental data, a mathematical model of an experimental laboratory sample is developed. This installation will optimize the operation of a vertical axis wind generator by creating a wind flow control system for further converting the wind flow into electrical energy. © 2022 IEEE.

Non-autoclaved aerated concrete (NAAC) is gaining attention for its strength-to-weight ratio and sustainability benefits. Produced by incorporating a blowing agent into a binder, aggregate, and water mixture, NAAC offers a lightweight and porous construction material. Ash and slag waste (ASW), primarily composed of silicon, aluminum, iron, and calcium oxides, presents significant potential as a sustainable additive. However, industrial-scale processing of ASW still needs to be explored in Kazakhstan. This study evaluates the feasibility of utilizing ASW from the Ust-Kamenogorsk Thermal Power Plant to produce earthquake-resistant NAAC. Incorporating 31.5% ASW by weight optimizes compressive strength, achieving 2.35 MPa and significantly improving the mechanical properties. Chemical and microstructural analyses confirm ASW’s suitability as a construction material. The study also introduces innovative processing methods and explores convolutional neural network models for predicting material structure changes, providing insights into optimizing production processes. The findings address the research objectives by confirming the viability of ASW in NAAC production and demonstrating its potential for sustainable construction. The results offer a pathway for industrial-scale applications, contributing to waste utilization and resource conservation. © 2024 by the authors.

Graphene oxide-based membranes hold great promise in composite materials for applications such as wastewater treatment and oil–water separation. In this study, classical molecular dynamics simulations were employed to investigate the separation of water from an oil–water mixture using a two-layer graphene oxide membrane. The effects of random and stripe-like grafting patterns on penetration efficiency were explored, focusing on varying grafting densities. The results show that increasing grafting density reduces permeability of both oil and water molecules, highlighting the critical role of surface functionalization in membrane design. Notably, the stripe grafting pattern significantly enhances penetration efficiency by optimizing steric interactions around the nanoslit. These findings contribute to the development of nanocomposite materials and surface modification techniques, offering insights into the design of membranes with high performance for oil–water separation. Understanding relationship between grafting density, surface patterning, and membrane performance is crucial for advancing hybrid materials that address industrial challenges such as wastewater treatment and oil spill remediation. The insights gained from this study can be further refined by exploring different functional groups and surface modifications, broadening the applications of these membranes in industrial separation processes. © The Author(s), under exclusive licence to Springer Nature Switzerland AG 2024.

In recent years, the development of nanomaterials with biocidal properties has received considerable attention due to their potential applications in various industries, including food, medicine, and cultural heritage preservation. The growing demand for coatings with antibacterial properties has sparked interest from industrial sectors in exploring the incorporation of biocides into these materials. Coatings are prone to microbial growth, which can cause damage such as cracking, discoloration, and staining. To combat these problems, the integration of biocides into coatings is a crucial strategy. Biocide-embedded nanomaterials offer numerous advantages, including high efficiency in small quantities, ease of application, good chemical stability, low toxicity, and non-bioaccumulation. Encapsulated nanobiocides are particularly attractive to the agro-industry, because they can be less toxic than traditional biocides while still effectively controlling microbial contamination. To fully exploit the benefits of nanobiocides, future research should focus on optimizing their synthesis, formulation, and delivery methods. The purpose of this review is to summarize the current status of biocide nanomaterials, discuss potential future research directions, and highlight research methods, the development of new forms of nanomaterials, and studies of their physico-chemical properties. Biocide nanocapsules of DCOIT (4,5-Dichloro-2-octyl-2H-isothiazol-3-one) are chosen as an example to illustrate the research pathways. © 2024 by the authors.
Flood modelling in snow-fed river basins is critical for understanding the impacts of climate change on hydrological extremes. The Zhabay River in northern Kazakhstan exemplifies a basin highly vulnerable to seasonal floods, which pose significant risks to infrastructure, livelihoods, and water resource management. Traditional flood forecasting in Central Asia still relies on statistical models developed during the Soviet era, which are limited in their ability to incorporate non-stationary climate and anthropogenic influences. This study addresses this gap by applying the Soil and Water Integrated Model (SWIM) to project climate-driven changes in the hydrological regime of the Zhabay River. The study employs a process-based, high-resolution hydrological model to simulate flood dynamics under future climate conditions. Historical hydrometeorological data were used to calibrate and validate the model at the Atbasar gauge station. Future flood scenarios were simulated using bias-corrected outputs from an ensemble of General Circulation Models (GCMs) under Representative Concentration Pathways (RCPs) 4.5 and 8.5 for the periods 2011–2040, 2041–2070, and 2071–2099. This approach enables the assessment of seasonal and interannual variability in flood magnitudes, peak discharges, and their potential recurrence intervals. Findings indicate a substantial increase in peak spring floods, with projected discharge nearly doubling by mid-century under both climate scenarios. The study reveals a 1.8-fold increase in peak discharge between 2010 and 2040, and a twofold increase from 2041 to 2070. Under the RCP 4.5 scenario, extreme flood events exceeding a 100-year return period (2000 m3/s) are expected to become more frequent, whereas the RCP 8.5 scenario suggests a stabilization of extreme event occurrences beyond 2071. These findings underscore the growing flood risk in the region and highlight the necessity for adaptive water resource management strategies. This research contributes to the advancement of climate-resilient flood forecasting in Central Asian river basins. The integration of process-based hydrological modelling with climate projections provides a more robust framework for flood risk assessment and early warning system development. The outcomes of this study offer crucial insights for policymakers, hydrologists, and disaster management agencies in mitigating the adverse effects of climate-induced hydrological extremes in Kazakhstan. © 2025 by the authors.
Показано 501–510 из 1309